Коды ошибок Riso RP
Error type |
Error details |
T |
Serviceman-call error |
A |
Jam error |
B |
Option error |
C |
Consumable error |
D |
Set check error |
E |
Warning (Serviceman call) |
F |
Warning (Other) |
G |
Paper-jam error |
Error point |
Error details |
0XX |
System (hardware, software, communication), panel |
1XX |
Scanning section (scanner, AF), image processing |
2XX |
Master making section |
3XX |
Master-disposal section |
4XX |
Paper-feed/ejection section |
5XX |
Print-drum area |
6XX |
Printing adjustment section (vertical, horizontal, density) |
7XX |
Accessories 1 |
8XX |
Accessories 2 |
Error type |
details |
T01 |
Main motor lock |
T02 |
Elevator motor lock |
T03 |
Clamp motor lock |
T04 |
Overflow |
T05 |
Print-positioning pulse-motor lock |
T06 |
Horizontal pulse-motor lock |
T07 |
Digitizer error |
T08 |
Computer interface error |
T09 |
Option error (paper eject) |
T10 |
Option error (paper feed) |
T11 |
Pressure-control motor |
T12 |
Master-disposal-section motor lock |
T13 |
Cutter motor lock |
T14 |
Flatbed error |
T15 |
AF error |
T17 |
Solenoid counter not connected |
T19 |
Thermal-pressure motor lock |
T20 |
Paper-ejection-section motor lock |
T22 |
Drum-lock error |
T23 |
Scanner lock not released |
T24 |
Inking motor lock |
T25 |
No battery |
T93 |
NET-C hardware error |
T94 |
TPH connection error |
T95 |
MCTL PCB backup error |
T96 |
Drum hardware error |
T98 |
Hardware error |
A01 |
Master feed error |
A02 |
Master loading error |
A03 |
Cutting error |
A04 |
Master-disposal error |
A05 |
Master present in the master-disposal section |
A06 |
Check paper-feed tray |
A07 |
Paper-feed error |
A08 |
Paper jam on print drum |
A09 |
Paper-ejection error |
A10 |
AF original feed error |
A16 |
Awaiting master removal |
A17 |
Cutter error |
A18 |
Print-drum unlocked |
B01 |
Keycard counter: No card |
B02 |
Sorter: Error command 1 |
B03 |
Sorter: Error command 2 |
B04 |
Sorter: Error command 3 |
B05 |
Sorter: Error command 4 |
B06 |
Multi -tray: Main-unit error |
B07 |
Multi -tray: Main-unit error |
B08 |
Multi -tray: Main-unit error |
B09 |
Multi -tray: Main-unit error |
B10 |
Multi -tray: Tray-1 error |
B11 |
Multi -tray: Tray-1 error |
B13 |
Multi -tray: Tray-1 error |
B14 |
Multi -tray: Tray-1 error |
B16 |
Multi -tray: Tray-2 error |
B17 |
Multi -tray: Tray-2 error |
B19 |
Multi -tray: Tray-2 error |
B20 |
Multi -tray: Tray-2 error |
B21 |
Data storage: Read/write error |
B22 |
Job separator: Power off |
B23 |
Job separator: No tape |
B24 |
Job separator: Tape jam |
B25 |
Sorter: Error command 5 |
B26 |
Sorter: Error command 6 |
B27 |
Sorter: Error command 7 |
B28 |
Sorter: Error command 8 |
B31 |
Linked printer data communication error |
B33 |
IP address set up error |
C01 |
Replace ink cartridge |
C02 |
Replace master roll |
C03 |
Master-disposal box full |
D01 |
Print drum not set |
D02 |
Incorrect print drum |
D03 |
Ink cartridge not set |
D04 |
Incorrect ink cartridge |
D05 |
Master not set |
D07 |
Master-disposal box not set |
D08 |
Master-disposal unit not set |
D09 |
Master making unit not set |
D10 |
Scanner table not set |
D11 |
Front cover not set |
D12 |
Feed-joint pass. Cover not set. |
E01 |
Replace battery |
E02 |
Maintenance call |
F01 |
No master on drum |
F02 |
Master image larger than paper size: 1 |
F04 |
Original not set |
F05 |
Print quantity under "minimum print quantity’ |
F07 |
Drum-position error |
F08 |
Paper size / Original size: Mismatch |
F10 |
Master image larger than paper size: 2 |
F11 |
Master image larger than paper size: 3 |
F12 |
Original size irregular: Triple-Tray Source selection invalid |
F16 |
AF cannot be used for QT-4 |
F17 |
Drum size does not match |
F18 |
Incorrect zoom rate |
F19 |
Master image larger than paper size: 4 |
F20 |
Master image larger than paper size: 5 |
F21 |
AF multi-up: Original not set |
F22 |
FB multi-up: Original not set |
F23 |
Communication error: D to P |
F24 |
Auto-reproduction size selection: Unable |
F25 |
Incorrect image resolution |
F26 |
Incorrect paper size: Long-paper mode |
F30 |
Multiple paper feed |
F31 |
Auto-stack tray error |
F32 |
Data storage area full |
F33 |
Master image size / Drum size: Mismatch |
F37 |
AF cannot be used in book mode |
F40 |
No paper in paper-feed tray: Triple-Tray Source |
F41 |
No paper in tray 1: Triple-Tray Source |
F42 |
No paper in tray 2: Triple-Tray Source |
F43 |
D to P Original size / Paper size: Mismatch |
F44 |
Auto reproduction size selection: Unable |
F49 |
Printer-Auto-Selection to linked printer disabled: Job setting error |
F50 |
Printer-Auto-Selection to linked printer disabled: Linked printer error |
F51 |
No Original on Scanner Table: Duplex Scanning Mode |
F52 |
Printing from Linked Printer Disabled: Configuration Data being acquired |
F53 |
More than 999 copies at one time not possible from linked printer |
F54 |
Printer-Auto-Selection to linked printer disabled: Selected paper not in linked printer |
F55 |
Printer-Auto-Selection to linked printer disabled: Receiving print data from PC |
F56 |
Printer-Auto-Selection to linked printer disabled: Config. Data being acquired |
F57 |
Printing from Linked Printer Disabled: Processing print data from PC |
F58 |
Printing from Linked Printer Disabled: Initializing NET-C |
F59 |
Printer-Auto-Selection to linked printer disabled: Initializing NIC |
F60 |
Printer-Auto-Selection to linked printer disabled: Print quantity selected is Zero |
F61 |
Linked Printer paper size and original size do not match |
L01 |
Error while in obtaining Management Information Base (MIB) |
Bit |
Corresponding value |
Error type |
Description |
Bit 0 |
1 |
A10 |
AF original feed error |
Bit 1 |
2 |
B03 |
Sorter: Error command 2 |
Bit 2 |
4 |
B07 |
Multi-tray: Main-unit error |
Bit 3 |
8 |
B09 |
Multi-tray: Main-unit error |
Bit 4 |
16 |
B11 |
Multi-tray: Tray-1 error |
Bit 5 |
32 |
B17 |
Multi-tray: Tray-2 error |
Bit 6 |
64 |
A07 |
Paper-feed error |
Bit 7 |
128 |
A08 |
Paper jam on print drum |
Bit 8 |
256 |
A09 |
Paper-ejection error |
Error type |
Panel display |
Panel display |
Gxxx Paper Jam Remove Paper in Indicated Areas and Press [OK] Button. |
Error type |
T01 [Main-motor lock] |
Panel display |
T01-*** !!System Error!! Press Reset Key If Recovery has Failed, Call Service |
Reset method |
Jam reset |
Error point |
Error conditions |
520 |
The main motor limit sensor does not go ON/OFF for more than 16 pulses while the main motor is operating, even after the elapse of 100 ms. |
521 |
The position-A sensor does not go ON/OFF, between two detections of position-B, while the main motor is operating. |
522 |
The position-B sensor does not go ON/OFF while the motor is operating, even when 3033 pulses are received at the Main FG. |
524 |
The clamp unit is not at the home position while the print drum is operating (Clamp sensor C: OFF, except during master disposal). |
536 |
The drum failed to stop at position A (over-run) |
537 |
The drum failed to stop at position B. (over-run) |
538 |
The print drum is not locked during operation. (Print-drum lock position sensor: OFF) |
Error type |
T02 [Elevator motor lock] |
Panel display |
T02-*** !!System Error!! Press Reset Key If Recovery has Failed, Call Service |
Reset method |
Jam reset or switch on power again |
Error point |
Error conditions |
400 |
Both the upper and lower limit sensors were ON. |
401 |
An overload current was detected in the elevator motor. |
404 |
The lower-limit sensor does not go OFF within 2 s after the elevator motor operates in the raising direction from the lower-limit position. |
405 |
The upper-limit sensor does not go ON within 12 s after the elevator motor operates in the raising direction. |
406 |
The upper-limit sensor does not go OFF within 2 s after the elevator motor operates in the lower direction from the upper-limit position. |
407 |
The lower-limit sensor does not go ON within 12 s after the elevator motor operates in the lowering direction. |
408 |
The upper-limit sensor is OFF continuously for at least 2 s during operation of the elevator servo. |
Error type |
T03 [Clamp motor] |
Panel display |
T03-*** !!System Error!! Press Reset Key If Recovery has Failed, Call Service |
Reset method |
Jam reset or switch on power again |
Error point |
Error conditions |
500 |
Clamp sensor C turns OFF following clamp unit initialization. |
501 |
Clamp sensors A and B do not change within 800 ms when the clamp motor operates in reverse during clamp unit initialization (clamp sensor A starts at OFF). |
502 |
Clamp sensors A and B do not change within 800 ms when the clamp motor operates in the forward direction during clamp unit initialization (clamp sensor A starts at ON). |
503 |
Clamp sensor C does not go OFF within 800 ms when the clamp moves from the home position. |
504 |
The clamp does not move from the home position to the open position within 800 ms during the operation of the clamp. |
505 |
The clamp does not move from the open position to the position-A compensation position within 800 ms during the operation of the clamp. |
506 |
The clamp does not move from the position-A compensation position to the clamp close position within 800 ms during the clamp operation. |
507 |
The command does not coincide with the current position when clamp operation is started. |
508 |
The command does not coincide with the stop position when clamp operation is stopped. |
Error type |
T-04 [Overflow] |
Panel display |
T04-*** !!System Error!! Press Reset Key If Recovery has Failed, Call Service |
Reset method |
Jam reset or switch on power again |
Error point |
Error conditions |
513 |
The overflow sensor was ON for a set number of times in succession during the 10- ms-interval overflow-sensor check. |
Error type |
T05 [Print-positioning pulse-motor lock] |
Panel display |
T05-*** !!System Error!! Press Reset Key If Recovery has Failed, Call Service |
Reset method |
Jam reset or switch on power again |
Error point |
Error conditions |
603 |
The vertical-centering sensor does not switch OFF -> ON even when the vertical- positioning pulse motor is moved 12 mm in the ON direction. |
604 |
The vertical-centering sensor does not switch ON -> OFF even when the vertical- positioning pulse motor is moved 12 mm in the OFF direction. |
610 |
Timeout error during the vertical-print-position return operation |
614 |
Vertical-print-position returning time out error |
616 |
The one-step-positioning key was pressed with vertical-print-pos ition information undefined. |
Error type |
T06 [Horizontal pulse-motor lock] |
Panel display |
T06-*** !!System Error!! Press Reset Key If Recovery has Failed, Call Service |
Reset method |
Jam reset or switch on power again |
Error point |
Error conditions |
605 |
The horizontal-centering sensor does not switch OFF -> ON even when the horizontal pulse motor is moved 12 mm in the ON direction. |
606 |
The horizontal-centering sensor does not switch ON -> OFF even when the horizontal pulse motor is moved 10 mm in the OFF direction. |
611 |
Timeout error during horizontal-print-position return operation |
615 |
Horizontal-print-position returning time out error |
617 |
The one-step-positioning key was pressed with the horizontal-print-position information undefined. |
Error type |
T07 [Digitizer error] |
Panel display |
T07 *** !!System Error!! Turn Main-Power SW OFF Then ON If Recovery has Failed, Call Service |
Reset method |
Switch power on again |
Error point |
Error conditions |
001 |
Communication error with the digitizer CPU |
Error type |
T08 [Computer interface error] |
Panel display |
T08-*** !!System Error!! Turn Main-Power SW OFF Then ON If Recovery has Failed, Call Service |
Reset method |
Switch power on again |
Error point |
Error conditions |
002 |
Communication error with the computer interface |
Error type |
T09 [Option error (paper eject)] |
Panel display |
T09-*** !!System Error!! Turn Main-Power SW OFF Then ON If Recovery has Failed, Call Service |
Reset method |
Switch power on again |
Error point |
Error conditions |
003 |
Communication error with the sorter |
700 |
Sorter communication: CTS does not switch to L within 3000 ms after the power is switched ON. |
701 |
Sorter communication: The type status was not returned within 200 ms after the initialization command was sent. |
710 |
Sorter communication: Transmission timeout |
711 |
Sorter communication: CTS does not change. |
712 |
Sorter communication: The retry command was sent but not received. |
720 |
Sorter communication: The retry command was received two times in succession. |
Error type |
T10 [Option error (paper feed)] |
Panel display |
T10 *** !!System Error!! Turn Main-Power SW OFF Then ON If Recovery has Failed, Call Service |
Reset method |
Switch power on again |
Error point |
Error conditions |
801 |
The type status was not returned from the multi-tray unit when the power was switched ON. |
802 |
The Standby OK command was not returned when printing started. |
803 |
The status was not returned from the multi-tray unit. |
840 |
An undefined multi-tray-unit command was received. |
841 |
CAN controller initialization failed. |
Error type |
T11 [Pressure-control motor lock] |
Panel display |
Tii *** !!System Error!! Press Reset Key If Recovery has Failed, Call Service |
Reset method |
Jam reset or switch on power again |
Error point |
Error conditions |
600 |
Timeout error for reducing pressure (OFF -> ON) during print-pressure home positioning. |
601 |
Timeout error for increasing pressure (ON -> OFF) during print-pressure home positioning. |
602 |
The print-pressure limit sensor does not change during print-pressure operation. |
620 |
Print-pressure operation was called with the print-pressure motor locked. |
621 |
Incorrect print-pressure operation timing (print-pressure operation command was received when the print-pressure should not change). |
622 |
Sensor A is ON and sensor B is OFF during movement from area Ato area D. |
623 |
Either sensor A or sensor B is ON during movement from area D to area A |
624 |
The current area data is undefined. |
625 |
The target area data is undefined. |
626 |
Timeout during relative print-pressure movement. |
Error type |
T12 [Master-disposal-section motor lock] |
Panel display |
T12 *** !!System Error!! Press Reset Key If Recovery has Failed, Call Service |
Reset method |
Jam reset or switch on power again |
Error point |
Error conditions |
305 |
The master compression sensor does not go ON within 6.5 s after the master compression motor operates in the return direction. |
306 |
Master compression sensor does not go OFF within 2 s after the master compression motor operates in the compress direction. |
307 |
The master compression sensor does not go ON within 6.5 s after the master compression motor operates in the compress direction, and the master- compression-motor limit sensor cannot count up until the compression-limit position. |
309 |
The master-compression-motor limit sensor does not change within 200 ms during compression operation. |
Error type |
T13 [Cutter motor lock] |
Panel display |
T13 *** !!System Error!! Press Reset Key If Recovery has Failed, Call Service |
Reset method |
Jam reset or switch on power again |
Error point |
Error conditions |
203 |
Cutter HP SW does not go OFF within 100 ms after the cutter motor is activated. |
204 |
Cutter HP SW does not go OFF -> ON within 300 ms after the cutter motor is activated. |
205 |
The master-positioning sensor is ON when the print drum rotates through the preset angle following cutting, and the master-positioning sensor is still ON when the print drum rotates through the preset angle following repeat cutting. |
Error type |
T14 [Flatbed error] |
Panel display |
T14-*** !!System Error!! Turn Main-Power SW OFF Then ON If Recovery has Failed, Call Service |
Reset method |
Switch power on again |
Error point |
Error conditions |
112 |
The FB/ADF HP sensor does not go OFF within the set time. |
113 |
The FB/ADF HP sensor does not go ON within the set time. |
114 |
Incorrect main-unit setting data |
115 |
The scanner operation is not completed within the set time. |
116 |
Timeout error for waiting black shading compensation |
117 |
Timeout error for waiting white shading compensation |
118 |
Scanner operation command was received when it should not move. (400/300 DPI) |
140 |
Communication error from the scanner unit (NAK twice, undefined error, etc.) |
141 |
Communication timeout error from the scanner unit (Receive timeout) |
142 |
The scanner unit detects a sequence error from the Risograph. |
150 |
Timeout error for receiving the Risograph scanner command |
151 |
The Risograph received an undefined command from the scanner. |
152 |
The Risograph detected a communication sequence error from the scanner. |
153 |
Risograph scanner communication error (ACK, NAK, or received-channel error) |
154 |
The Risograph could not send data to the scanner within the set time. |
160 |
Scanner connection error |
Error type |
T15 [ADF error] |
Panel display |
T15-*** !!System Error!! Turn Main-Power SW OFF Then ON If Recovery has Failed, Call Service |
Reset method |
Switch power on again |
Error point |
Error conditions |
004 |
Communication error with the ADF/CPU units |
100 |
Original IN sensor adjustment error |
101 |
ADF-EEPROM error |
108 |
ADF guide potentiometer error |
110 |
ADF operation not completed within the set time |
120 |
Communication error from the ADF unit (NAK twice, undefined error, etc.) |
121 |
Communication timeout error from the ADF unit (Receive timeout) |
122 |
The ADF unit detects a sequence error from the Risograph. |
130 |
Timeout error for receiving the Risograph ADF command |
131 |
The Risograph received an undefined command from the ADF unit. |
132 |
The Risograph detected a communication sequence error from the ADF unit. |
133 |
Risograph ADF communication error (ACK, NAK, or received-channel error) |
134 |
The Risograph could not send to the ADF within the set time. |
161 |
ADF connection error |
Error type |
T17 [Solenoid counter not connected] |
Panel display |
T17 *** !!System Error!! Press Reset Key If Recovery has Failed, Call Service |
Reset method |
Set the solenoid counter connection signal to ON |
Error point |
Error conditions |
020 |
The solenoid counter is not connected. |
Error type |
T19 [Thermal-pressure motor lock] |
Panel display |
T19 *** !!System Error!! Press Reset Key If Recovery has Failed, Call Service |
Reset method |
Jam reset or switch power on again |
Error point |
Error conditions |
207 |
The TPH pressure sensor does not go OFF within 2 s after the thermal-pressure motor activates in the counterclockwise direction. |
208 |
The TPH pressure sensor does not go ON within 2 s after the thermal-pressure motor activates in the counterclockwise direction. |
216 |
The TPH pressure sensor does not go OFF within 2 s after the thermal-pressure motor activates in the clockwise direction. |
217 |
The TPH pressure sensor does not go ON within 2 s after the thermal-pressure motor activates in the clockwise direction. |
Error type |
T20 [Paper-ejection-section motor lock] |
Panel display |
T20 *** !!System Error!! Press Reset Key If Recovery has Failed, Call Service |
Reset method |
Jam reset |
Error point |
Error conditions |
414 |
The paper-ejection-wing home sensor does not go ON within the set time after the paper-ejection-wing motor activates in the clockwise direction during paper-ejection wing home positioning. |
415 |
The paper-ejection-wing home sensor does not go OFF within 250 ms after the paper ejection wing motor activates in the counterclockwise direction from home position during paper ejection wing positioning. |
416 |
An overload current was detected in the paper-ejection motor. |
424 |
The paper-ejection limit sensor gives fewer than 20 pulses within 100 ms. |
Error type |
T22 [Drum lock error] |
Panel display |
T22 *** !!System Error!! Press Reset Key If Recovery has Failed, Call Service |
Reset method |
Jam reset or switch power on again |
Error point |
Error conditions |
514 |
Failed to stop at position B during print-drum locking |
516 |
The print-drum lock position sensor does not go OFF within 500 ms after the printdrum locking motor activates. |
517 |
The print-drum lock cam sensor does not go ON within 1 s after the print-drum locking motor activates. |
518 |
The print-drum lock position sensor does not go ON within 500 ms after the printdrum locking motor activates. |
519 |
The print-drum lock cam sensor does not go OFF within 1 s after the print-drum locking motor activates. |
529 |
The print-drum lock-position sensor and print-drum lock cam sensor are both ON. |
530 |
The print-drum lock cam sensor does not go ON within 2 s after the print-drum locking motor activates during drum lock initialization. |
531 |
The print-drum lock position sensor does not go ON within 2 s after the print-drum locking motor activates during drum lock initialization. |
549 |
The print-drum lock-position sensor does not go ON during locking of the printdrum lock unit. |
556 |
The print-drum lock-position sensor is OFF while the print drum is not set. |
Error type |
T23 [Scanner lock not released] |
T23 *** | |
Panel display |
Image Scanner is Locked!! |
Unlock it | |
Reset method |
Release the scanner lock in test mode |
Error point |
Error conditions |
111 |
In scanner lock mode |
Error type |
T24 [Inking motor lock] |
Panel display |
T24 *** !!System Error!! Press Reset Key If Recovery has Failed, Call Service |
Reset method |
Jam reset or switch power on again |
Error point |
Error conditions |
539 |
Inking-motor current overload |
Error type |
T25 [No battery] |
Panel display |
T25-*** !!System Error!! Turn Main-Power SW OFF Then ON If Recovery has Failed, Call Service |
Reset method |
Switch power on again |
Error point |
Error conditions |
026 |
The residual battery voltage is below 2.3 V when the power is ON. |
Error type |
T93 [NET-C hardware error] |
Panel display |
T93-*** !!System Error!! Turn Main-Power SW OFF Then ON If Recovery has Failed, Call Service |
Reset method |
Switch power on again |
Error point |
Error conditions |
932 |
No reply from NET-C. NET-C does not recognize hardware reset of NET-C, or does not detect initialization command from RP, etc. |
933 |
No response from NET-C for 90 seconds during NET-C initialization. |
Error type |
T94 [TPH not connected] |
Panel display |
T94-*** !!System Error!! Press Reset Key If Recovery has Failed, Call Service |
Reset method |
Jam reset or switch on power again |
Error point |
Error conditions |
225 |
TPH not connected. |
Error type |
T95 [MCTL PCB backup error] |
Panel display |
T95-*** !!System Error!! Turn Main-Power SW OFF Then ON If Recovery has Failed, Call Service |
Reset method |
Switch power on again |
Error point |
Error conditions |
036 |
Backup data size does not match with that of NVRAM rated data size. |
056 |
NVRAM check-sum error in the MCTL PCB |
059 |
Serial-number data sent from SH-PCB does not match the MCTL PCB serialnumber data. |
Error type |
T96 [Drum hardware error] |
Panel display |
T96-*** !!System Error!! Pull Out Print Drum and Replace it If Recovery has Failed, Call Service |
Reset method |
Pull out the print drum or switch the power on again |
Error point |
Error conditions |
552 |
Print-drum data backup error |
Error type |
T98 [Hardware error] |
Panel display |
T98-*** !!System Error!! Turn Main-Power SW OFF Then ON If Recovery has Failed, Call Service |
Reset method |
Switch power on again |
Error point |
Error conditions |
005 |
Type-code error |
029 |
Straight paper feed (multi-tray unit) paper width VR setting is not made. |
030 |
Tray 1 (multi-tray unit) paper width VR setting is not made. |
031 |
Tray 2 (multi-tray unit) paper width VR setting is not made. |
046 |
The DIMM capacity does not match. |
051 |
Touch-panel communication error |
052 |
EEPROM read error |
053 |
Memory settings (program, mode, user paper), failed to read the save data |
054 |
Memory settings (program, mode, user paper), failed to write save data |
055 |
The machine type code from SH-PCB does not match the type data from the MCTL PCB. |
057 |
SRAM backup error in the SH-PCB |
058 |
SH-PCB serial-number data is all set to zero. |
063 |
The test-mode setting data stored was set outside the adjustment range. |
064 |
An undefined command was sent in communication between SH-PCB and MCTL PCB. |
065 |
Communication error 01 between SH-PCB and MCTL PCB (MCTL PCB side) |
068 |
Communication error 04 between SH-PCB and MCTL PCB (MCTL PCB side) |
069 |
Communication error 05 between SH-PCB and MCTL PCB (MCTL PCB side) |
070 |
Communication error 06 between SH-PCB and MCTL PCB (MCTL PCB side) |
071 |
Communication error 07 between SH-PCB and MCTL PCB (MCTL PCB side) |
072 |
Communication error 08 between SH-PCB and MCTL PCB (SH-PCB side) |
073 |
Communication error 09 between SH-PCB and MCTL PCB (SH-PCB side) |
074 |
Communication error 10 between SH-PCB and MCTL PCB (SH-PCB side) |
075 |
Communication error 11 between SH-PCB and MCTL PCB (SH-PCB side) |
076 |
Communication error 12 between SH-PCB and MCTL PCB (SH-PCB side) |
077 |
Communication error 12 between SH-PCB and MCTL PCB (SH-PCB side) |
078 |
Communication error 14 between SH-PCB and MCTL PCB (SH-PCB side) |
079 |
Communication error 15 between SH-PCB and MCTL PCB (SH-PCB side) |
080 |
Communication error 16 between SH-PCB and MCTL PCB (SH-PCB side) |
081 |
Communication error 17 between SH-PCB and MCTL PCB (SH-PCB side) |
082 |
Communication error 18 between SH-PCB and MCTL PCB (SH-PCB side) |
083 |
Communication error 19 between SH-PCB and MCTL PCB (SH-PCB side) |
084 |
Communication error 20 between SH-PCB and MCTL PCB (SH-PCB side) |
Error type |
T98 [Hardware error] |
Panel display |
T98-*** !!System Error!! Turn Main-Power SW OFF Then ON If Recovery has Failed, Call Service |
Reset method |
Switch power on again |
Error point |
Error conditions |
085 |
User settings (properties, test-mode adjustment values), failed to read save data |
086 |
User settings (properties, test-mode adjustment values), failed to write save data |
087 |
Memory settings (program, mode, user paper), no save data set |
088 |
User settings (properties, test-mode adjustment values), no save data set |
089 |
No.1 of the Dip switches on SH-PCB is set to ON. |
090 |
Machine code of memory settings (program, mode, user paper) does not match. |
091 |
Check sum of memory settings (program, mode, user paper), does not match. |
092 |
Machine code of User settings (properties, test-mode adjustment values), does not match. |
093 |
Check sum of user settings (properties, test-mode adjustment values), does not match. |
094 |
Communication sequence error between SH-PCB and MCTL PCB (MCTL side) |
095 |
Check sum of user settings (properties, test-mode adjustment values), does not match during stand-by. |
096 |
Check sum of memory settings (program, mode, user paper), does not match, during stand-by. |
097 |
Test mode adjustments memorized in the drum is outside the adjustment range. |
099 |
ROSE: Error in data processing |
219 |
The TPH size code does not match the machine-type code data. |
220 |
The TPH resolution code does not match the machine-type code data. |
422 |
The transmitter adjustment DA setting reached the upper limit during text-mode No. 457 Auto Multi-Paper-Feed Det. Adj. |
423 |
The transmitter adjustment DA setting reached the lower limit during text-mode No. 457 Auto Multi-Paper-Feed Det. Adj. |
526 |
Drum set safety switch is ON, but drum connection signal is OFF. |
540 |
Print-drum communication: Gate-array timeout |
541 |
Print-drum communication: ROM-writing-complete timeout |
614 |
Print-pressure jig: Outside the adjustment range |
922 |
ROSE: System lock (Image communication error) |
998 |
MCTL: System lock (System overload) |
Error type |
A01 [Master feed error] |
Panel display |
A01-*** Master Misfeed Rewind Master Roll and Reset Master in Place |
Reset method |
Master-making-unit sensor: OFF -> ON, then master-positioning sensor OFF (or switch the power on again) |
Error point |
Error conditions |
201 |
The master-positioning sensor does not go ON even after the write pulse motor and load pulse motor are activated during the master-positioning operation. |
202 |
The master-positioning sensor does not go OFF even when the write pulse motor is reversed during the master-positioning operation. |
211 |
The master-positioning sensor was ON during standby. |
214 |
The master-positioning sensor was ON at the start of master making. |
215 |
Faulty gate-array control for the write pulse motor or load pulse motor (motor does not stop within set time) |
222 |
Master feed error (error occurred during error recovery movement) |
Error type |
A02 [Master loading error] |
Panel display |
A02-*** Master Misfeed Rewind Master Roll and Reset Master in Place |
Reset method |
Master-manufacturing unit sensor: OFF -> ON |
Error point |
Error conditions |
509 |
The master-loading sensor was OFF when the master was checked at a specified drum angle during the master-loading operation. |
555 |
Master loading error (error occurred during error recovery movement) |
Error type |
A03 [Cutting error] |
Panel display |
A03-*** Master Was Not Loaded on Print Drum Correctly Pull Out Print Drum and Remove Master |
Reset method |
Print-drum set sensor: OFF -> ON |
Error point |
Error conditions |
206 |
Master cut was successful after master cut retry. |
224 |
Master cutting error (error occurred during error recovery movement) |
Error type |
A04 [Master-disposal error] |
Panel display |
A04-*** Master-Disposal Error Pull Out Print Drum and Discard Master |
Reset method |
Print-drum set sensor: OFF -> ON |
Error point |
Error conditions |
303 |
Master-disposal jam sensor was OFF at both 120 and 180 degrees drum angle. |
304 |
The master-disposal jam sensor was ON at completion of master-disposal operation. |
315 |
Master-disposal error (error occurred during recovery movement). |
316 |
Master-disposal jam sensor was OFF during recovery movement. |
Error type |
A05 [Master present in the master-disposal section] |
Panel display |
A05-*** Master Jammed in Disposal Unit Open Scanner Table and Disposal Top Cover, then Remove Master |
Reset method |
Master-disposal-unit set sensor: OFF C25-> ON, and master-disposal jam sensor: ON. (Or switch the power on again.) |
Error point |
Error conditions |
312 |
The master-disposal jam sensor was ON at the start of master making operation. |
Error type |
A06 [Check paper-feed tray] |
Panel display |
A06-*** Check Standard Feed Tray |
Reset method |
The paper-feed-tray lower/upper safety switch goes ON. (Or switch the power on again.) |
Error point |
Error conditions |
403 |
The paper-feed-tray upper or lower safety switch was OFF. |
433 |
The paper-feed-tray upper or lower safety switch became OFF while tray in motion. |
Error type |
A07 [Paper-feed error] |
Panel display |
|
Reset method |
Turn the paper sensor OFF and reset the jam (or switch the power on again). |
Error point |
Error conditions |
409 |
The paper-ejection sensor was OFF when the paper should have arrived, and the paper sensor was ON at 180°, just before stopping. |
412 |
The paper sensor was OFF three times in succession when a paper misfeed was detected (paper misfeed). |
418 |
The paper sensor was ON at the start of operation. |
429 |
Paper feed error (error occurred during recovery movement) |
Error type |
A08 [Paper jam on print drum] |
Reset method |
Print-drum set sensor: OFF -> ON (Or switch the power on again.) |
Error point |
Error conditions |
410 |
The paper-ejection sensor was OFF when paper should have arrived, and the paper sensor was OFF at 180° just before stopping. |
421 |
The paper sensor was ON when the paper should have left the paper sensor during feeding of long paper in long-length paper mode (paper longer than 555 mm). |
430 |
Paper jam on print drum (error occurred during recovery movement). |
B29 |
Error command (Main unit: Jam error) received from the multi-tray unit. During machine idling, Multi-tray feed sensor 4 is ON and Paper sensor is also ON. |
Error type |
A09 [Paper-ejection error] |
Reset method |
Turn the paper-ejection sensor OFF and reset the jam, or switch the power on again. |
Error point |
Error conditions |
411 |
The paper-ejection sensor was ON when the paper should have left the paper- ejection sensor. |
417 |
The paper-ejection sensor was ON at the start of operation. |
4З1 |
Paper-ejection error (error occurred during recovery movement) |
Error type |
A10 [AF original feed error] |
Reset method |
Turn the AF original detection sensor OFF, and reset the jam. |
Error point |
Error conditions |
102 |
Original-registration-sensor remaining jam |
103 |
Original-IN-sensor remaining jam |
104 |
Original-OUT-sensor remaining jam |
105 |
Original-registration-sensor non-arrival jam |
106 |
Original-IN-sensor non-arrival jam |
107 |
Original-OUT-sensor non-arrival jam |
109 |
An original feed error occurred, due to opening the AF. |
162 |
No original in AF during AF master making. |
Error type |
A16 [Awaiting master removal] |
Panel display |
A16-*** Master Remains on Print Drum Pull Out Print Drum and Remove Master |
Reset method |
Print-drum set sensor: OFF -> ON |
Error point |
Error conditions |
525 |
Awaiting master removal. |
554 |
Remove master (master is detected on drum while in recovery movement). |
Error type |
A17 [Cutter error] |
Panel display |
A17 *** !!System Error!! Rewind Master Roll and Close Scanner Table |
Reset method |
Master-loading set unit: OFF -> ON; master-detection sensor: OFF. |
Error point |
Error conditions |
209 |
The cutter home-position switch was OFF during master setting at the start of master making. |
221 |
Cutter error (error occurred during recovery movement). |
Error type |
A18 [Print drum unlocked] |
Panel display |
A18-*** Print Drum has been Unlocked To Lock it Again, Pull it Out and Then Set it Back in Place |
Reset method |
Print-drum safety switch: OFF -> ON |
Error point |
Error conditions |
528 |
The print-drum lock position sensor is OFF and the print-drum lock cam sensor is ON, while the print-drum sensor safety switch is ON. |
Error type |
B01 [Keycard counter: No card] |
Panel display |
B01-*** Insert Card into Key/Card Counter |
Reset method |
Insert Card |
Error point |
Error conditions |
730 |
Keycard counter: No card |
Error type |
B02 [Sorter: Error command 1] |
Panel display |
B02-*** Check Sorter Panel Display |
Reset method |
Check Sorter |
Error point |
Error conditions |
702 |
An error command was received (Serviceman-call error) from the sorter. |
Error type |
B03 [Sorter: Error command 2] |
Reset method |
Remove jammed paper |
Error point |
Error conditions |
703 |
An error command was received (Jam error) from the sorter. |
Error type |
B04 [Sorter: Error command 3] |
Panel display |
B04-*** Close Sorter Cover |
Reset method |
Close the cover |
Error point |
Error conditions |
707 |
An error command was received (Open error) from the sorter. |
Error type |
B05 [Sorter: Error command 4] |
Panel display |
B05-*** Check Sorter Panel Display |
Reset method |
Check the sorter |
Error point |
Error conditions |
709 |
An error command was received (others) from the sorter. |
Error type |
B06 [Multi-tray: Main-unit error (Serviceman-call error)] |
Panel display |
B06-*** !!System Error!! Turn Main-Power SW OFF Then ON If Recovery has Failed, Call Service |
Reset method |
Jam reset or switch power on again |
Error point |
Error conditions |
804 |
An error command was received (Main unit: Serviceman-call error) from the multitray unit. Even after 100 ms after the multi-tray transfer motor was turned ON, multitray feed limit sensor did not count any pulses. |
Error type |
B07 [Multi-tray: Main-unit error (Jam-Feed joint pass)] |
Reset method |
Sensor on paper-feed path -> OFF, jam reset, or switch the power on again |
Error point |
Error conditions |
825 |
Error command received (Main unit: Jam error) from the multi-tray unit. After multitray feed sensor 3 turns ON, and multi-tray transfer motor rotates a certain amount of pulses, the multi-tray feed sensor 4 did not turn ON (Multi-tray feed sensor 1&2=OFF, 3=ON), or multi-tray feed sensor 3 is ON when the power is turned ON. |
826 |
Error command received (Main unit: Jam error) from the multi-tray unit. After multitray feed sensor 4 turns ON, and multi-tray transfer motor rotates a certain amount of pulses, the paper sensor did not turn ON (Multi-tray feed sensors 1&2=OFF and 3&4=ON), or multi-tray feed sensors 3&4 are ON when power is turned ON. |
827 |
Error command received (Main unit: Jam error) from the multi-tray unit. When the machine is in idle, the multi-tray feed sensors 3&4 are ON and paper sensor is ON. |
828 |
Error command received (Main unit: Jam error) from the multi-tray unit. After multitray feed sensor 4 turns ON, and multi-tray transfer motor rotates a certain amount of pulses, the paper sensor did not turn ON (Multi-tray feed sensors 1 to 3=OFF and 4=ON), or multi-tray feed sensor is ON when the power is turned ON. |
Error type |
B08 [Multi-tray: Main-unit error (Multi-tray transfer unit open)] |
Panel display |
B08-*** Close Multi-Tray Transfer Unit |
Reset method |
Jam reset or switch power on again |
Error point |
Error conditions |
805 |
Error command received (Main unit: Open error) from the multi-tray unit. Multi-tray transfer unit was opened. |
Error type |
B09 [Multi-tray Main-unit error (Jam-Multi tray transfer)] |
Reset method |
Sensor on paper-feed path -> OFF, jam reset, or switch the power on again |
Error point |
Error conditions |
816 |
Error command received (Main unit: Jam error) from the multi-tray unit. After multitray feed sensor 1 turns ON, and multi-tray transfer motor rotates a certain amount of pulses, the multi-tray feed sensor 2 did not turn ON (Multi-tray feed sensor 1 stayed ON ), or multi-tray feed sensor 1 is ON when the power is turned ON. |
817 |
Error command received (Main unit: Jam error) from the multi-tray unit. After multitray feed sensor 2 turns ON, and multi-tray transfer motor rotates a certain amount of pulses, the multi-tray feed sensor 3 did not turn ON (Multi-tray feed sensor 1,2 stayed ON ), or multi-tray feed sensors 1&2 are ON when the power is turned ON. |
818 |
Error command received (Main unit: Jam error) from the multi-tray unit. After multitray feed sensor 3 turns ON, and multi-tray transfer motor rotates a certain amount of pulses, the multi-tray feed sensor 4 did not turn ON (Multi-tray feed sensors 1 to 3 stayed ON), or multi-tray feed sensors 1 to 3 are ON when the power is turned ON. |
819 |
Error command received (Main unit: Jam error) from the multi-tray unit. After multitray feed sensor 4 turns ON, and multi-tray transfer motor rotates a certain amount of pulses, the paper sensor did not turn ON (Multi-tray feed sensors 1 to 4 stayed ON), or multi-tray feed sensors 1 to 4 are ON when the power is turned ON. |
820 |
Error command received (Main unit: Jam error) from the multi-tray unit. During the machine idling, the multi-tray feed sensors 1 to 4 are ON and the paper sensor is ON. |
821 |
Error command received (Main unit: Jam error) from the multi-tray unit. After multitray feed sensor 2 turns ON, and multi-tray transfer motor rotates a certain amount of pulses, the multi-tray feed sensor 3 did not turn ON (Multi-tray feed sensor 1=OFF, 2=ON), or multi-tray feed sensor 2 is ON when the power is turned ON. |
822 |
Error command received (Main unit: Jam error) from the multi-tray unit. After multitray feed sensor 3 turns ON, and multi-tray transfer motor rotates a certain amount of pulses, the multi-tray feed sensor 4 did not turn ON. (Multi-tray feed sensor 1=OFF, 2&3=ON), or multi-tray feed sensors 2&3 are ON when the power is turned ON. |
823 |
Error command received (Main unit: Jam error) from the multi-tray unit. After multitray feed sensor 4 turns ON, and multi-tray transfer motor rotates a certain amount of pulses, the paper sensor did not turn ON (Multi-tray feed sensor 1=OFF, 2 to 4=ON), or multi-tray feed sensors 2 to 4 are ON when the power is turned ON. |
824 |
Error command received (Main unit: Jam error) from the multi-tray unit. During the machine idling, the multi-tray feed sensors 2 to 4 are ON and the paper sensor is ON. |
825 |
Error command received (Main unit: Jam error) from the multi-tray unit. After multitray feed sensor 3 turns ON, and multi-tray transfer motor rotates a certain amount of pulses, the multi-tray feed sensor 4 did not turn ON (Multi-tray feed sensors 1&2=OFF, 3=ON), or multi-tray feed sensor 3 is ON when power is turned ON. |
Error type |
B10 [Multi-tray: Tray-1 error (Serviceman call)] |
Panel display |
B10-*** !!System Error!! Turn Main-Power SW OFF Then ON If Recovery has Failed, Call Service |
Reset method |
Jam reset or switch power on again |
Error point |
Error conditions |
806 |
Error command received (Tray 1: Serviceman-call error) from the multi-tray unit. Even after 7 sec after multi-tray 1 elevator motor turned ON, the upper limit sensor does not turn ON. |
Error type |
B11 [Multi-tray: Tray-1 error (Jam: Upper)] |
Reset method |
Reset tray |
Error point |
Error conditions |
807 |
Error command received (Tray 1: Jam error) from the multi-tray unit. Paper misfeed from tray 1. (Multi-tray feed sensor 3 is OFF) |
842 |
In feeding from tray 1, paper sensor stayed OFF even though the paper should have reached the paper sensor. |
Error type |
B13 [Multi-tray: Tray-1 error (Multi-tray unit open)] |
Panel display |
B13-*** Set Feed Tray 1 in Place |
Reset method |
Set tray |
Error point |
Error conditions |
809 |
Error command received (Tray 1: Open error) from the multi-tray unit. |
Error type |
B14 [Multi-tray: Tray-1 error (Check tray)] |
Panel display |
B14-*** Check Feed Tray 1 |
Reset method |
Jam reset or switch power on again |
Error point |
Error conditions |
810 |
Error command received (Tray 1: Check-tray error) from the multi-tray unit. Multi-tray 1 limit switch is ON. |
Error type |
B^ [Multi-tray: Tray-2 error (Serviceman call)] |
Panel display |
!!System Error!! Turn Main-Power SW OFF Then ON If Recovery has Failed, Call Service |
Reset method |
Jam reset or switch power on again |
Error point |
Error conditions |
B11 |
Error command received (Tray 2: Serviceman-call error) from the multi-tray unit. Even after 7 sec after multi-tray 2 elevator motor turned ON, the upper limit sensor did not change to ON. |
Error type |
B17 [Multi-tray Tray-2 error (Jam)] |
Reset method |
Reset tray |
Error point |
Error conditions |
B12 |
Error command received (Tray 2: Jam error) from the multi-tray unit. Paper misfeed from tray 2. (Multi-tray feed sensor 1 is OFF) |
B43 |
Misfeed when paper is fed from tray 2 |
Error type |
B19 [Multi-tray Tray-2 error (Tray-2 open)] |
Panel display |
B19-*** Set Feed Tray 2 in Place |
Reset method |
Set tray |
Error point |
Error conditions |
B14 |
Error command received (Tray 2: Open error) from the multi-tray unit. |
Error type |
B20 [Multi-tray Tray-2 error (Check tray)] |
Panel display |
B20 *** Check Feed Tray 2 |
Reset method |
Jam reset or switch power on again |
Error point |
Error conditions |
B15 |
Error command received (Tray 2: Check-tray error) from the multi-tray unit. Multi-feed tray 2 limit SW is ON. |
Error type |
B21 [Data storage: Read/Write error] |
Panel display |
B21 *** !!System Error!! Turn Main-Power SW OFF Then ON If Recovery has Failed, Call Service |
Reset method |
Switch power ON again. |
Error point |
Error conditions |
714 |
Data-storage file-name error |
715 |
Data-storage access error |
716 |
Other data-storage error |
Error type |
B22 [Job separator: Power off] |
Panel display |
B22 *** !!Job Separator Has No Power!! Turn ON Power Switch of it |
Reset method |
Check and switch ON the power of job separator. |
Error point |
Error conditions |
721 |
With the "Tape separation" function set ON, no power is supplied to the job separator when start key is pressed. |
727 |
After cluster-A signal turned ON, BUSY-signal stayed "L" more than 4 sec. |
Error type |
B23 [Job separator: No tape] |
Panel display |
B23 *** No Paper Tape in Job Separator Replace Tape Roll |
Reset method |
Check and set paper tape in job separator. |
Error point |
Error conditions |
722 |
With the "Tape separation" function set ON, no tape detected when the start key is pressed. |
723 |
No tape remains upon completion of the tape-ejection operation. |
Error type |
B24 [Job separator: Tape jam] |
Panel display |
B24-*** Paper-Tape Jam in Job Separator Remove Paper Tape |
Reset method |
Check and remove the jammed paper from job separator. |
Error point |
Error conditions |
724 |
Tape remains when the start key is pressed with the "Tape separation" function set to ON. |
725 |
The tape-jam detection signal is "H" within 500 ms after the cluster-A signal turns ON (tape misfeed). |
726 |
The tape-jam detection signal is "L" when the BUSY signal changes from "L" to "H" (or after 5 sec. at "L") after the cluster-A signal goes ON (tape misfeed). |
Error type |
B26 [Sorter: Error command 6 (Print on bin error)] |
Panel display |
B26 *** Check Sorter Panel Display |
Reset method |
Remove the paper from sorter. |
Error point |
Error conditions |
705 |
Error command (Paper on bin error) received from the sorter |
Error type |
B27 [Sorter: Error command 7 (Staple error)] |
Panel display |
B27 *** Check Sorter Panel Display |
Reset method |
Clear the stapler jam. |
Error point |
Error conditions |
706 |
Error command (Staple error) received from the sorter |
Error type |
B28 [Sorter: Error command 8 (Size error)] |
Panel display |
B28 *** Check Sorter Panel Display |
Reset method |
Remove paper from sorter. |
Error point |
Error conditions |
708 |
Error command (Size error) received from the sorter |
Error type |
B31 [Linked Printer: Communication error during data transmission] |
Panel display |
B31-*** Data transfer Error for Linked Printer Check Network and Linked Printers Then Transfer Data Again |
Reset method |
Check Network and Linked Printer Panel Message |
Error point |
Error conditions |
920 |
Error detected by NET-C. (No signal from linked printer, connection interrupted, NET-C TCP/IP is not activating, interruption from RP, etc.) |
Error type |
B25 [Sorter: Error command 5 (Full error)] |
Panel display |
B25-*** Check Sorter Panel Display |
Reset method |
Remove the paper from sorter. |
Error point |
Error conditions |
704 |
Error command (Full error) received from the sorter |
Error type |
B33 [IP address set up error] |
Panel display |
B33-*** No IP Address Assigned to This Printer Contact Network Administrator |
Reset method |
Assign correct IP address |
Error point |
Error conditions |
931 |
IP address is not assigned to RP. With no IP address assigned, the link is enabled on the linked printer. |
Error type |
C01 [Replace ink cartridge] |
Panel display |
C01-*** No Ink Replace Ink Cartridge |
Reset method |
Ink-cartridge set sensor: OFF -> ON |
Error point |
Error conditions |
512 |
The ink sensor did not go ON even when inking was performed for the preset period. |
Error type |
C02 [Replace master roll] |
Panel display |
C02-*** No Master Replace Master Roll |
Reset method |
Master-making unit sensor: OFF -> ON and Master detection sensor: OFF -> ON |
Error point |
Error conditions |
200 |
The master end was detected twice in succession at 10-ms intervals during master transport. |
Error type |
C03 [Master disposal box full] |
Panel display |
C03-*** Empty Master Disposal Box |
Reset method |
Disposal-box safety switch: OFF for more than 5 sec and then ON. |
Error point |
Error conditions |
308 |
The compression detection position was reached before the master-compression- motor limit-sensor count reached the specified level, after the master compression motor turned ON in the compression direction. |
Error type |
D01 [Print drum not set] |
Panel display |
D01-*** Set Print Drum in Place |
Reset method |
Print-drum safety switch to ON and Print-drum set signal to ON |
Error point |
Error conditions |
527 |
Both the print-drum safety switch and print drum set signal is OFF. |
547 |
The print-drum set signal is ON, but the print-drum safety switch is OFF. |
Error type |
D02 [Incorrect print drum] |
Panel display |
D02-*** Wrong-Type Print Drum Installed |
Reset method |
Replace with correct print drum. |
Error point |
Error conditions |
532 |
Incorrect print drum is used. |
Error type |
D03 [Ink cartridge not set] |
Panel display |
D03-*** Install Ink Cartridge |
Reset method |
Ink-cartridge set sensor: ON |
Error point |
Error conditions |
533 |
The ink-cartridge set sensor is OFF. |
Error type |
D04 [Incorrect ink cartridge] |
Panel display |
D04-*** Wrong-Type Ink Cartridge Installed |
Reset method |
Replace with correct ink cartridge. |
Error point |
Error conditions |
534 |
Incorrect ink cartridge is used. |
Error type |
D05 [Master not set] |
Panel display |
D05-*** Master Not Set in Place Insert Lead Edge of Master into Master Entrance and Close Master-Making Unit |
Reset method |
Master detection sensor: ON |
Error point |
Error conditions |
210 |
The master detection sensor is OFF (not detecting master). |
223 |
Master not set (Error occurred in error recovery movement) |
Error type |
D07 [Master disposal box not set] |
Panel display |
D07-*** Set Master Disposal Box in Place |
Reset method |
Disposal-box safety switch: ON |
Error point |
Error conditions |
310 |
The disposal-box safety switch is OFF. |
Error type |
D08 [Master disposal unit not set] |
Panel display |
D08-*** Close Disposal Top Cover |
Reset method |
Disposal-top-cover sensor: ON |
Error point |
Error conditions |
311 |
The disposal-top-cover sensor is OFF (sensor light path is free). |
Error type |
D09 [Master-making unit not set] |
Panel display |
D09-*** Close Master-Making Unit |
Reset method |
Master-making-unit sensor: ON |
Error point |
Error conditions |
212 |
The master-making-unit sensor is OFF (sensor light path is free). |
Error type |
D10 [Scanner table not set] |
Panel display |
D10-*** Close Scanner Table |
Reset method |
Flatbed set switch: ON |
Error point |
Error conditions |
213 |
The flatbed set switch is OFF. |
Error type |
D11 [Front cover not set] |
Panel display |
Du *** Close Front Cover |
Reset method |
Front-cover switch: ON |
Error point |
Error conditions |
535 |
The front-cover switch is OFF. |
Error type |
D12 [Feed-joint pass. Cover not set] |
Panel display |
D12 *** Close Feed-Joint Passage Cover |
Reset method |
Feed-joint pass. Cover safety switch: ON. |
Error point |
Error conditions |
551 |
Feed-joint pass. The cover safety switch is OFF. |
Error type |
E01 [Replace battery] |
Panel display |
!! Battery Replacement !! Call Service |
Reset method |
Jam reset |
Error point |
Error conditions |
010 |
The battery voltage was less than 2.5 V when the power was switched ON (weak battery: time to replace battery). |
Error type |
E02 [Maintenance call] |
Panel display |
!! Maintenance !! Call Service |
Reset method |
Jam reset |
Error point |
Error conditions |
011 |
The master counter reached the value set in test mode when the power was ON, the unit was reset, or operation ended. |
012 |
The copy counter reached the value set in test mode when the power was ON, the unit was reset, or operation ended. |
022 |
The maintenance counter inside the print drum reached the value set in test mode when the power was ON, the unit was reset, or operation ended. |
Error type |
F01 [No master on drum] |
Panel display |
No Master on Print Drum Make a New Master |
Reset method |
Close, reset, or change mode. |
Error point |
Error conditions |
015 |
There is no master on the print drum at the start of printing. |
Error type |
F02 [Master image larger than paper size: 1] |
Panel display |
Page Form at Larger than Paper Size !! Possible Ink Smudges on Prints !! (Continue -> START Key) |
Reset method |
Stop, reset, or start. |
Error point |
Error conditions |
018 |
The paper size does not match the image on the print drum at the start of printing. |
Error type |
F04 [Original not set (Multi-page mode)] |
Panel display |
Place Another Original and Press Start Key To Cancel, Press Stop Key |
Reset method |
Set original. |
Error point |
Error conditions |
013 |
The original is not set when multi-page mode was started. |
Error type |
F05 [Print quantity under "Minimum print quantity"] |
Panel display |
Enter Print Quantity Over ** Programmed Minimum Value |
Reset method |
Set a print quantity over the minimum print quantity. |
Error point |
Error conditions |
019 |
In master making, the print quantity selected is under the minimum print quantity. |
Error type |
F07 [Drum-position error] |
Panel display |
!! Print Drum is Not in Neutral Position !! Press Print-Position Centering Key to Shift Back Print Drum |
Reset method |
Press centering key. |
Error point |
Error conditions |
014 |
The print drum is not centered at the start of master making. |
Error type |
F08 [Paper size / original size: mismatch] |
Panel display |
!! The Current Paper Size is not Correct !! Change Paper Size |
Reset method |
Change the paper size or original size. |
Error point |
Error conditions |
017 |
Paper size corresponding to the original size is not set for Triple-Tray Source selection. |
Error type |
F10 [Master image larger than paper size: 2] |
Panel display |
!! Page Format Larger than Paper Size !! Possible Ink Smudges on Prints (Continue -> TEST PRINT Key) |
Reset method |
Stop, reset, or start test printing. |
Error point |
Error conditions |
021 |
The paper size does not match the image on the print drum at the start of test printing. |
Error type |
F11 [Master image larger than paper size: 3] |
Panel display |
!! Another Size of Paper has been Loaded on the Standard Feed Tray !! Change Paper Data |
Reset method |
Select the paper size on the paper-feed tray (master making size). |
Error point |
Error conditions |
023 |
At the start of the master making or when the paper on the paper-feed-tray was changed, the paper size does not match the image size. |
Error type |
F12 [Original size irregular: Triple-Tray Source selection invalid] |
Panel display |
!! No Auto Paper Size Selection with Irregular Size Original !! Select Paper Size |
Reset method |
Close or reset. |
Error point |
Error conditions |
024 |
A non-standard-size original was set at the start of operation with the Triple-Tray Source selected. |
Error type |
F16 [AF cannot be used for QT-4] |
Panel display |
!! No QT-4 Sheets for Original Scanning in AF !! Place Original on the Platen Glass |
Reset method |
Remove the original from the AF. |
Error point |
Error conditions |
039 |
The original was set on the AF when operation was started with QT-4 selected. |
Error type |
F17 [Drum size does not match] |
Panel display |
!! The Print Drum Type has been Changed !! Select the Current Print Drum Type |
Reset method |
Select the print-drum size. |
Error point |
Error conditions |
027 |
Different size print drum from the previous is set. |
Error type |
F18 [Incorrect zoom rate] |
Panel display |
!! Images may not fit in Frame of paper with this Reproduction Size !! Check Current Selection (Continue -> START Key) |
Reset method |
Change reproduction size, or start master-making operation. |
Error point |
Error conditions |
043 |
The paper size does not match the original size reproduction size when the master- making operation is started with the manual tray selected. |
Error type |
F19 [Master image larger than paper size: 4] |
Panel display |
!! Another Size of Paper has been Loaded on Feed Tray 1 !! Change Paper Data |
Reset method |
Select the paper size for tray 1. |
Error point |
Error conditions |
040 |
The paper size selected does not match that of the actual paper loaded when the paper in tray 1 was replaced. |
Error type |
F20 [Master image larger than paper size: 5] |
Panel display |
!! Another Size of Paper has been Loaded on Feed Tray 2 !! Change Paper Data |
Reset method |
Select the paper size for tray 2. |
Error point |
Error conditions |
041 |
The paper size selected does not match that of the actual paper loaded when the paper in tray 2 was replaced. |
Error type |
F21 [AF multi-up: Original not set] |
Panel display |
Place Another Original To Cancel, Press Stop Key |
Reset method |
Set original on the AF, or cancel the operation. |
Error point |
Error conditions |
032 |
The next original is not in placed on AF for multi-up operation. |
Error type |
F22 [FB multi-up: Original not set] |
Panel display |
Place Another Original and Press Start Key To Cancel, Press Stop Key |
Reset method |
Place original on the flatbed, or stop the FB multi-up operation. |
Error point |
Error conditions |
033 |
The next original is not placed on flatbed for multi-up operation. |
Error type |
F23 [Communication error: D to P] |
Panel display |
Communication Error Check Communication Devices and Cables |
Reset method |
Jam reset |
Error point |
Error conditions |
044 |
Communication error in remote mode (D to P mode) |
Error type |
F25 [Incorrect image resolution] |
Panel display |
!! The Image Resolution of the Current Data has Just been Converted !! (Continue -> START Key) |
Reset method |
Jam reset or start key |
Error point |
Error conditions |
045 |
Data is received with a inconsistent image resolution (D to P mode). |
Error type |
F26 [Incorrect paper size: Long-paper mode] |
Panel display |
!! Paper-Size Selection is Not Correct !! Change Selection |
Reset method |
Check the paper size. Press "OK" or "RESET" to clear the message. |
Error point |
Error conditions |
413 |
With the long-length paper mode not selected, the paper sensor is still ON when the paper should have left the paper sensor (the paper was a long-length paper). |
419 |
With the long-length paper mode selected, the paper left the paper sensor too soon (the paper was not a long-length paper). |
Error type |
F30 [Multiple paper feed] |
Panel display |
!! Possible Multiple Paper Feed !! Check Printed Copies |
Reset method |
Check the printed copies. Press "OK" or "RESET" to clear the message. |
Error point |
Error conditions |
420 |
Multiple paper feed is detected during operation (when no paper-ejection jam error exists). |
425 |
Paper conforming to data obtained in the light-transmission check is fed in multiple. |
426 |
Paper is fed in multiple during the light-transmission check. |
427 |
Paper conforming to data obtained in the paper-sensor OFF check is fed in multiple. |
428 |
Paper is fed in multiple during the paper-sensor OFF check. |
Error type |
F31 [Auto stack-tray error] |
Panel display |
Check Paper Receiving Tray |
Reset method |
Check the paper guides or press the start key. Press "OK" or "RESET" to clear the message. |
Error point |
Error conditions |
B36 |
The HP sensor does not go ON during paper-guide home positioning. |
B37 |
The HP sensor does not go OFF when the paper guides are moved. |
B3B |
The HP sensor does not go ON during paper-stopper home positioning. |
B39 |
The HP sensor does not go OFF when the paper stopper is moved. |
Error type |
F32 [Data storage area full] |
Panel display |
!! Data-Storage Area has Become Full !! Clear Old Storage Data |
Reset method |
Check the available storage area. Press "OK" or "RESET" to clear the message. |
Error point |
Error conditions |
713 |
Insufficient memory available when data is being written on the data-storage card. |
Error type |
F33 [Master image size / Drum size: mismatch] |
Panel display |
!! Unmatched Size -- Print Drum and Image Area !! Check Print Drum (Continue -> START Key) |
Reset method |
Check the print drum size, or start making master by pressing the start key. |
Error point |
Error conditions |
047 |
The master making size did not match the drum size when P-to-P master making is started. |
04B |
The master making size did not match the drum size when D-to-P master making is started. |
Error type |
F37 [AF cannot be used in book mode] |
Panel display |
!! Book Shadow Editor is Not Available with AF !! Place Original on Stage Glass |
Reset method |
Set the original on the flatbed, or cancel book mode. Press "OK" or "RESET" to clear the message. |
Error point |
Error conditions |
050 |
The original was set on the AF with book mode set when master making is started. |
Error type |
F40 [No paper in paper-feed tray: Triple-Tray Source] |
Panel display |
Load Paper in Standard Feed Tray |
Reset method |
Load paper. |
Error point |
Error conditions |
060 |
Paper ran out during proof printing with the standard (straight) feed tray selected from the Triple-Tray Source. |
907 |
Paper ran out during printing with the standard (straight) feed tray selected from the Triple-Tray Source. |
Error type |
F41 [No paper in tray 1: Triple-Tray Source] |
Panel display |
Load Paper in Feed Tray 1 |
Reset method |
Load paper. |
Error point |
Error conditions |
061 |
Paper ran out during proof printing with Tray 1 selected from the Triple-Tray Source. |
908 |
Paper ran out during printing with Tray 1 selected from the Triple-Tray Source. |
Error type |
F42 [No paper in tray 2: Triple-Tray Source] |
Panel display |
Load Paper in Feed Tray 2 |
Reset method |
Load paper. |
Error point |
Error conditions |
062 |
Paper ran out during proof printing with Tray 2 selected from the Triple-Tray Source. |
909 |
Paper ran out during printing with Tray 2 selected from the Triple-Tray Source. |
Error type |
F43 [D to P Original Size / Paper Size: Mismatch] |
Panel display |
!! Unmatched Size -- Current Page and Printing Paper !! Check Paper Size (Continue ->START Key) |
Reset method |
Check paper size, or press START Key to continue. |
Error point |
Error conditions |
900 |
Original size and paper size do not match at start of D to P master making. |
Error type |
F44 [Auto Reproduction Size Selection: Unable] |
Panel display |
!! No Auto Reproduction Size Selection w ith This Combination of Original and Printing Paper !! Select Size Manually |
Reset method |
Manually select the reproduction size. |
Error point |
Error conditions |
901 |
Original size could not be detected (original size out of detectable parameter). |
Error type |
F49 [Printer-Auto-Selection to linked printer disabled: Job setting error] |
Panel display |
!! No Printout on Linked Printer with the Current Print Job Setting !! Print will Start here (Continue ->START Key) |
Reset method |
Close, RESET or STOP to cancel, or press START Key to make prints from RP. |
Error point |
Error conditions |
906 |
Auto-printer-selection is disabled with current job setting. |
Error type |
F50 [Printer-Auto-Selection to linked printer disabled: Linked printer error] |
Panel display |
!! Linked Printer Error - No Printout on Linked Printer !! Print will Start here (Continue ->START Key) |
Reset method |
Close, RESET or STOP to cancel, or press START Key to make prints from RP. |
Error point |
Error conditions |
910 |
Auto-printer-selection is disabled with linked printer error. |
Error type |
F51 [No Original on Scanner Table: Duplex Scanning Mode] |
Panel display |
|
Reset method |
Press START Key (reverse side page scanning), or STOP or RESET (print front page only). |
Error point |
Error conditions |
911 |
No original on Scanner Table (Duplex Scanning: Waiting for original). |
Error type |
F52 [Printing from Linked Printer Disabled: Configuration Data being acquired] |
Panel display |
Acquiring Linked Printer Configuration Data Please Wait a Moment |
Reset method |
Change the mode. |
Error point |
Error conditions |
912 |
Cannot print from linked printer (Configuration data not acquired). |
Error type |
F53 [More than 999 copies at one time not possible from linked printer] |
Panel display |
!! No More than 999 Copies on Linked Printers !! Use This Printer (Number is to be Reset) |
Reset method |
Change the mode, or START Key to start (print out from RP). |
Error point |
Error conditions |
913 |
Designated print quantity on linked printer over the limit. |
Error type |
F54 [Printer-Auto-Selection to linked printer disabled: Selected paper not in linked printer] |
Panel display |
!! Selected Paper Size is Not Available on Linked Printers !! Print will Start here (Continue ->START Key) |
Reset method |
Close, RESET or STOP to cancel, or press START Key to make prints from RP. |
Error point |
Error conditions |
923 |
Auto-printer-selection is disabled due to the selected paper not in the linked printer. |
Error type |
F55 [Printer-Auto-Selection to linked printer disabled: Receiving print data from PC] |
Panel display |
!! No Printout on Linked Printers while Receiving Print Data from PC !! Print will Start here (Continue ->START Key) |
Reset method |
Close, RESET or STOP to cancel, or press START Key to make prints from RP. |
Error point |
Error conditions |
924 |
Auto-printer-selection is disabled while receiving print data from PC. |
Error type |
F56 [Printer-Auto-Selection to linked printer disabled: Config. Data being Acquired] |
Panel display |
!! No Printout on Linked Printers while Acquiring Their Config. Data !! Print will Start here (Continue ->START Key) |
Reset method |
Close, RESET or STOP to cancel, or press START Key to make prints from RP. |
Error point |
Error conditions |
925 |
Auto-printer-selection is disabled with no config. data in linked printer. |
Error type |
F57 [Printing from Linked Printer Disabled: Processing print data from PC] |
Panel display |
Processing Print Data from PC Linked Printers are Not Available while Processing Current Data |
Reset method |
Change the mode. |
Error point |
Error conditions |
926 |
Cannot print from linked printer (Processing job from PC). |
Error type |
F58 [Printing from Linked Printer Disabled: Initializing NET-C] |
Panel display |
Starting Up RISORINC-NET Please Wait a Moment |
Reset method |
Change the mode. |
Error point |
Error conditions |
927 |
Cannot print from linked printer (Initializing NET-C). |
Error type |
F59 [Printer-Auto-Selection to linked printer disabled: Initializing NIC] |
Panel display |
! ! No Printout on Linked Printers while Starting Up RISORINC-NET !! Print will Start here (Continue ->START Key) |
Reset method |
Close, RESET or STOP to cancel, or press START Key to make prints from RP. |
Error point |
Error conditions |
92B |
Auto-printer-selection is disabled due to initializing of NET-C. |
Error type |
F60 [Printer-Auto-Selection to linked printer disabled: Print quantity selected is Zero] |
Panel display |
!! No Printout on Linked Printers with "0" as Number of Copies !! Print will Start here (Continue ->START Key) |
Reset method |
Close, RESET or STOP to cancel, or press START Key to make prints from RP. |
Error point |
Error conditions |
929 |
Auto-printer-selection is disabled with print quantity selected as Zero. |
Error type |
F61 [Linked Printer paper size and original size do not match] |
Panel display |
!! Paper of the Specified Size is Not Prepared in Linked Printer !! Prepare it there |
Reset method |
Close, RESET or STOP. |
Error point |
Error conditions |
930 |
Linked printer paper size and original size mismatch. |