Установление причин неисправности Bizhub PRESS 1250/1250P/1052/PRO 951 (TROUBLESHOOTING)
bizhub PRESS 1052
Classification |
JAM Code |
Cause |
Tray1 |
J-1101 |
During operation: The paper feed sensor /1 (PS7) does not turn ON within a specified period of time after the paper feed clutch /1 (CL4) turns ON. |
|
J-1102 |
The pre-registration sensor /1 (PS17) does not turn ON within a specified period of time after the paper feed clutch /1 (CL4) turns ON. |
|
J-1103 |
During operation: The vertical conveyance sensor/1 (PS/19) does not turn ON within a specified period of time after the pre-registration sensor (PS17) turns ON. |
|
J-1104 |
During operation: When the trailing edge of paper is passing through the vertical conveyance sensor /1 (PS19), the preregistration sensor /1 (PS17) is turned ON by the succeeding paper. |
|
J-1151 |
When idling: The vertical conveyance sensor /1 (PS19) turns ON while in idling. |
|
J-1152 |
When idling: The pre-registration sensor /1 (PS/ 17) turns ON while in idling. |
Tray2 |
J-1201 |
During operation: The paper feed sensor /2 (PS11) does not turn ON within a specified period of time after the paper feed clutch /2 (CL6) turns ON. |
|
J-1202 |
During operation: The pre-registration sensor /2 (PS18) does not turn ON within a specified period of time after the paper feed clutch /2 (CL6) turns ON. |
|
J-1203 |
During operation: The pre-registration sensor /3 (PS21) does not turn ON within a specified period of time after the paper feed clutch /2 (PS18) turns ON. |
|
J-1204 |
During operation: When the trailing edge of paper is passing through the vertical conveyance sensor /3 (PS21), the preregistration sensor /2 (PS18) is turned ON by the succeeding paper. |
|
J-1251 |
When idling: The vertical conveyance sensor /3 (PS21) turns ON while in idling. |
|
J-1252 |
When idling: The pre-registration sensor /2 (PS/ 18) turns ON while in idling. |
Tray3 (PFU1) |
J-1301 |
During operation: PF-703 The paper feed sensor /1 (PS2) does not turn ON within a specified period of time after the paper feed clutch /1 (CL7) turns ON. (PF-706) The paper feed sensor /1 (PS3) does not turn ON within a specified period of time after the paper feed clutch /1 (CL6) turns ON. |
LU |
J-1301 |
During operation: The pre-registration sensor (PS107) does not turn ON within a specified period of time after the paper feed clutch (CL101) turns ON. |
Tray3 (PFU1) |
J-1302 |
During operation: (PF-703) The pre-registration sensor /1 (PS14) does not turn ON within a specified period of time after the paper feed clutch /1 (CL7) turns ON. (PF-706) The pre-registration sensor /1 (PS14) does not turn ON within a specified period of time after the paper feed clutch /1 (CL6) turns ON. |
LU |
J-1302 |
During operation: The LU exit sensor (PS106) does not turn ON within a specified period of time after the preregistration clutch (CL102) turns ON. |
Tray3 (PFU1) |
J-1303 |
During operation: (PF-703/706) The vertical conveyance sensor /1 (PS15) does not turn ON within a specified period of time after the pre-registration sensor /1 (PS14) turns ON. |
|
J-1304 |
During operation: (PF-703/706) When the trailing edge of paper is passing through the vertical conveyance sensor /1 (PS15), the pre-registration sensor /1 (PS14) is turned ON by the succeeding paper. |
LU |
J-1304 |
During operation: When the trailing edge of paper is passing through the LU exit sensor (PS106), the preregistration sensor (PS107) is turned ON by the succeeding paper. |
Tray3 (PFU1) |
J-1305 |
During operation: PF-703 The paper suction sensor Fr/1 (PS25) and the paper suction sensor /Rr1(PS26) do not turn ON within a specified period of time from the rotation stabilization standby (3sec) after the paper suction fan /1 (FM13) and the paper suction fan / 2 (FM14) turn ON. |
|
J-1351 |
When idling: (PF-703/706) The pre-registration sensor /1 (PS14) turns ON while in idling. |
LU |
J-1351 |
When idling: The LU exit sensor (PS106) turns ON while in idling. |
Tray3 (PFU1) |
J-1352 |
When idling: (PF-703/706) The vertical conveyance sensor /1 (PS15) turns ON while in idling. |
LU |
J-1352 |
When idling: The pre-registration sensor (PS107) turns ON while in idling. |
Tray4 (PFU1) |
J-1401 |
During operation: PF-703 The paper feed sensor /2 (PS6) does not turn ON within a specified period of time after the paper feed clutch /2 (CL8) turns ON. (PF-706) The paper feed sensor /2 (PS7) does not turn ON within a specified period of time after the paper feed clutch /2 (CL9) turns ON. |
|
J-1402 |
During operation: PF-703 The pre-registration sensor /2 (PS18) does not turn ON within a specified period of time after the paper feed clutch /2 (CL8) turns ON. (PF-706) The pre-registration sensor /2 (PS18) does not turn ON within a specified period of time after the paper feed clutch /2 (CL9) turns ON. |
|
J-1403 |
During operation: (PF-703/706) When the trailing edge of paper is passing through the loop sensor /2 (PS19), the preregistration sensor /2 (PS18) is turned ON by the succeeding paper. |
|
J-1405 |
During operation: PF-703 The paper suction sensor Fr/3 (PS27) and the paper suction sensor /Rr2(PS28) do not turn ON within a specified period of time from the rotation stabilization standby (3sec) after the paper suction fan /3 (FM15) and the paper suction fan / 4 (FM16) turn ON. |
|
J-1451 |
When idling: (PF-703/706) The pre-registration sensor /2 (PS18) turns ON while in idling. |
Tray5 (PFU1) |
J-1501 |
During operation: PF-703 The paper feed sensor /3 (PS10) does not turn ON within a specified period of time after the paper feed clutch /3 (CL9) turns ON. (PF-706) The paper feed sensor /3 (PS11) does not turn ON within a specified period of time after the paper feed clutch /3 (CL12) turns ON. |
|
J-1502 |
During operation: PF-703 The pre-registration sensor /3 (PS20) does not turn ON within a specified period of time after the paper feed clutch /3 (CL9) turns ON. (PF-706) The pre-registration sensor /3 (PS20) does not turn ON within a specified period of time after the paper feed clutch /3 (CL12) turns ON. |
|
J-1503 |
During operation: PF-703 The vertical conveyance sensor /3 (PS21) does not turn ON within a specified period of time after the pre-registration sensor /3 (PS20) turns ON. (PF-706) The vertical conveyance sensor /2 (PS21) does not turn ON within a specified period of time after the pre-registration sensor /3 (PS20) turns ON. |
|
J-1504 |
During operation: PF-703 When the trailing edge of paper is passing through the vertical conveyance sensor /3 (PS21), the pre-registration sensor /3 (PS20) is turned ON by the succeeding paper. (PF-706) When the trailing edge of paper is passing through the vertical conveyance sensor /2 (PS21), the pre-registration sensor /3 (PS20) is turned ON by the succeeding paper. |
|
J-1505 |
During operation: (PF-703) The paper suction sensor /Fr3 (PS29) and the paper suction sensor /Rr3 (PS30) do not turn ON within a specified period of time from the rotation stabilization standby (3sec) after the paper suction fan /5 (FM17) and the paper suction fan /6 (FM18) turn ON. |
|
J-1551 |
When idling: (PF-703/706) The pre-registration sensor /3 (PS20) turns ON while in idling. |
|
J-1552 |
When idling: PF-703 The vertical conveyance sensor /3 (PS21) turns ON while in idling. (PF-706) The vertical conveyance sensor /2 (PS21) turns ON while in idling. |
Tray6 (PFU2) |
J-1611 |
During operation: PF-703 The paper feed sensor /1 (PS2) does not turn ON within a specified period of time after the paper feed clutch /1 (CL7) turns ON. (PF-706) The paper feed sensor /1 (PS3) does not turn ON within a specified period of time after the paper feed clutch /1 (CL6) turns ON. |
|
J-1612 |
During operation: PF-703 The pre-registration sensor /1 (PS14) does not turn ON within a specified period of time after the paper feed clutch /1 (CL7) turns ON. (PF-706) The pre-registration sensor /1 (PS14) does not turn ON within a specified period of time after the paper feed clutch /1 (CL6) turns ON. |
|
J-1613 |
During operation: (PF-703/706) The vertical conveyance sensor /1 (PS15) does not turn ON within a specified period of time after the pre-registration sensor /1 (PS14) turns ON. |
|
J-1614 |
During operation: (PF-703/706) When the trailing edge of paper is passing through the vertical conveyance sensor /1 (PS15), the pre-registration sensor /1 (PS14) is turned ON by the succeeding paper. |
|
J-1615 |
During operation: PF-703 The paper suction sensor Fr/1 (PS25) and the paper suction sensor /Rr1(PS26) do not turn ON within a specified period of time from the rotation stabilization standby (3sec) after the paper suction fan /1 (FM13) and the paper suction fan / 2 (FM14) turn ON. |
Tray7 (PFU2) |
J-1621 |
During operation: PF-703 The paper feed sensor /2 (PS6) does not turn ON within a specified period of time after the paper feed clutch /2 (CL8) turns ON. (PF-706) The paper feed sensor /2 (PS7) does not turn ON within a specified period of time after the paper feed clutch /2 (CL9) turns ON. |
|
J-1622 |
During operation: PF-703 The pre-registration sensor /2 (PS18) does not turn ON within a specified period of time after the paper feed clutch /2 (CL8) turns ON. (PF-706) The pre-registration sensor /2 (PS18) does not turn ON within a specified period of time after the paper feed clutch /2 (CL9) turns ON. |
|
J-1623 |
During operation: (PF-703/706) When the trailing edge of paper is passing through the loop sensor /2 (PS19), the preregistration sensor /2 (PS18) is turned ON by the succeeding paper. |
|
J-1625 |
During operation: PF-703 The paper suction sensor Fr/3 (PS27) and the paper suction sensor /Rr2(PS28) do not turn ON within a specified period of time from the rotation stabilization standby (3sec) after the paper suction fan /3 (FM15) and the paper suction fan / 4 (FM16) turn ON. |
Tray8 (PFU2) |
J-1631 |
During operation: PF-703 The paper feed sensor /3 (PS10) does not turn ON within a specified period of time after the paper feed clutch /3 (CL9) turns ON. (PF-706) The paper feed sensor /3 (PS11) does not turn ON within a specified period of time after the paper feed clutch /3 (CL12) turns ON. |
|
J-1632 |
During operation: PF-703 The pre-registration sensor /3 (PS20) does not turn ON within a specified period of time after the paper feed clutch /3 (CL9) turns ON. (PF-706) The pre-registration sensor /3 (PS20) does not turn ON within a specified period of time after the paper feed clutch /3 (CL12) turns ON. |
|
J-1633 |
During operation: PF-703 The vertical conveyance sensor /3 (PS21) does not turn ON within a specified period of time after the pre-registration sensor /3 (PS20) turns ON. (PF-706) The vertical conveyance sensor /2 (PS21) does not turn ON within a specified period of time after the pre-registration sensor /3 (PS20) turns ON. |
|
J-1634 |
During operation: PF-703 When the trailing edge of paper is passing through the vertical conveyance sensor /3 (PS21), the pre-registration sensor /3 (PS20) is turned ON by the succeeding paper. (PF-706) When the trailing edge of paper is passing through the vertical conveyance sensor /2 (PS21), the pre-registration sensor /3 (PS20) is turned ON by the succeeding paper. |
|
J-1635 |
During operation: PF-703 The paper suction sensor /Fr3 (PS29) and the paper suction sensor /Rr3 (PS30) do not turn ON within a specified period of time from the rotation stabilization standby (3sec) after the paper suction fan /5 (FM17) and the paper suction fan /6 (FM18) turn ON. |
Paper feed conveyance (PFU2) |
J-1641 |
During operation: (PF-703/706) The intermediate sensor /Up (PS16) does not turn ON within a specified period of time after the vertical conveyance sensor /1 (PS15) turns ON. |
|
J-1642 |
During operation: (PF-703/706) The loop sensor /1 (PS17) does not turn ON within a specified period of time after the intermediate sensor /Up (PS16) turns ON. |
|
J-1643 |
During operation: (PF-703/706) The loop sensor /2 (PS19) does not turn ON within a specified period of time after the preregistration sensor /2 (PS18) turns ON. |
|
J-1644 |
During operation: PF-703 The intermediate sensor /Lw (PS22) does not turn ON within a specified period of time after the vertical conveyance sensor /3 (PS21) turns ON. (PF-706) The intermediate sensor /Lw (PS22) does not turn ON within a specified period of time after the vertical conveyance sensor /2 (PS21) turns ON. |
|
J-1645 |
During operation: (PF-703/706) The loop sensor /3 (PS23) does not turn ON within a specified period of time after the intermediate sensor /Lw (PS22) turns ON. |
|
J-1646 |
During operation: (PF-703/706) The PF exit conveyance sensor (PS24) does not turn ON within a specified period of time after the loop sensor /1 (PS17) turns ON. |
|
J-1647 |
During operation: (PF-703/706) The PF exit conveyance sensor (PS24) does not turn ON within a specified period of time after the loop sensor /2 (PS19) turns ON. |
|
J-1648 |
During operation: (PF-703/706) The PF exit conveyance sensor (PS24) does not turn ON within a specified period of time after the loop sensor /3 (PS23) turns ON. |
Tray6 (PFU2) |
J-1651 |
When idling: (PF-703/706) The pre-registration sensor /1 (PS14) turns ON while in idling. |
|
J-1652 |
When idling: (PF-703/706) The vertical conveyance sensor /1 (PS15) turns ON while in idling. |
Tray7 (PFU2) |
J-1661 |
When idling: (PF-703/706) The pre-registration sensor /2 (PS18) turns ON while in idling. |
Tray8 (PFU2) |
J-1671 |
When idling: (PF-703/706) The pre-registration sensor /3 (PS20) turns ON while in idling. |
|
J-1672 |
When idling: PF-703 The vertical conveyance sensor /3 (PS21) turns ON while in idling. (PF-706) The vertical conveyance sensor /2 (PS21) turns ON while in idling. |
Tray6 (PFU2) |
J-1681 |
When idling: (PF-703/706) The intermediate sensor /Up (PS16) turns ON while in idling. |
|
J-1682 |
When idling: (PF-703/706) The loop sensor /1 (PS17) turns ON while in idling. |
Tray7 (PFU2) |
J-1683 |
When idling: (PF-703/706) The loop sensor /2 (PS19) turns ON while in idling. |
Tray8 (PFU2) |
J-1684 |
When idling: (PF-703/706) The intermediate sensor /Lw (PS22) turns ON while in idling. |
|
J-1685 |
When idling: (PF-703/706) The loop sensor /3 (PS23) turns ON while in idling. |
Paper feed conveyance (PFU2) |
J-1686 |
When idling: (PF-703/706) The PF exit conveyance sensor (PS24) turns ON while in idling. |
Paper feed conveyance (common to each tray) |
J-1701 |
During operation: The ADU pre-registration sensor (PS40) does not turn ON within a specified period of time after the ADU conveyance sensor (PS42) turns ON. |
|
J-1702 |
During operation: The ADU pre-registration sensor (PS42) does not turn ON within a specified period of time after the ADU conveyance sensor (PS16) turns ON. |
Paper feed conveyance (Tray/1, /2) |
J-1703 |
During operation: The vertical conveyance sensor (PS16) does not turn ON within a specified period of time after the vertical conveyance sensor /1 (PS19) turns ON. |
Paper feed conveyance (Tray2) |
J-1704 |
During operation: The vertical conveyance sensor /2 (PS20) does not turn ON within a specified period of time after the vertical conveyance sensor /3 (PS21) turns ON. |
|
J-1705 |
During operation: The vertical conveyance sensor /1 (PS19) does not turn ON within a specified period of time after the vertical conveyance sensor /2 (PS20) turns ON. |
Paper feed conveyance (PFU) |
J-1706 |
During operation: (PF-703/706) The loop sensor (PS16) of the main body does not turn ON within a specified period of time after the PF exit conveyance sensor (PS24) turns ON. |
LU |
J-1706 |
During operation: The loop sensor (PS54) does not turn ON within a specified period of time after the LU exit sensor (PS106) turns ON. |
Paper feed conveyance |
J-1712 |
During operation: The multi feed detection board /S (MFDBS) or /R (MFDBR) detects the double feed.However, envelopes cannot be detected depending on the paper size. (PRO 951 is unimplemented) |
|
J-1751 |
When idling: The vertical conveyance sensor (PS41) turns ON while in idling. |
|
J-1752 |
When idling: The pre-registration sensor (PS40) turns ON while in idling. |
|
J-1753 |
When idling: The pre-registration sensor (PS42) turns ON while in idling. |
|
J-1754 |
When idling: The pre-registration sensor (PS16) turns ON while in idling. |
|
J-1755 |
When idling: The vertical conveyance sensor /2 (PS20) turns ON while in idling. |
Paper feed conveyance (PFU1) |
J-1801 |
During operation: (PF-703/706) The intermediate sensor /Up (PS16) does not turn ON within a specified period of time after the vertical conveyance sensor /1 (PS15) turns ON. |
|
J-1802 |
During operation: (PF-703/706) The loop sensor /1 (PS17) does not turn ON within a specified period of time after the intermediate sensor /Up (PS16) turns ON. |
|
J-1803 |
During operation: (PF-703/706) The loop sensor /2 (PS19) does not turn ON within a specified period of time after the preregistration sensor /2 (PS18) turns ON. |
|
J-1804 |
During operation: PF-703 The intermediate sensor /Lw (PS22) does not turn ON within a specified period of time after the vertical conveyance sensor /3 (PS21) turns ON. (PF-706) The intermediate sensor /Lw (PS22) does not turn ON within a specified period of time after the vertical conveyance sensor /2 (PS21) turns ON. |
|
J-1805 |
During operation: (PF-703/706) The loop sensor /3 (PS23) does not turn ON within a specified period of time after the intermediate sensor /Lw (PS22) turns ON. |
|
J-1806 |
During operation: (PF-703/706) The PF exit conveyance sensor (PS24) does not turn ON within a specified period of time after the loop sensor /1 (PS17) turns ON. |
|
J-1807 |
During operation: (PF-703/706) The PF exit conveyance sensor (PS24) does not turn ON within a specified period of time after the loop sensor /2 (PS19) turns ON. |
|
J-1808 |
During operation: (PF-703/706) The PF exit conveyance sensor (PS24) does not turn ON within a specified period of time after the loop sensor /3 (PS23) turns ON. |
Horizontal conveyance (PFU1) |
J-1810 |
During operation: (PF-703) The horizontal conveyance sensor /1 (PS31) does not turn ON within a specified period of time after the PF exit conveyance sensor (PS24) turns ON. |
|
J-1811 |
During operation: (PF-703) The horizontal conveyance sensor /2 (PS32) does not turn ON within a specified period of time after the horizontal conveyance sensor /1 (PS31) turns ON. |
|
J-1812 |
During operation: (PF-703) The horizontal conveyance sensor /3 (PS33) does not turn ON within a specified period of time after the horizontal conveyance sensor /2 (PS32) turns ON. |
|
J-1813 |
During operation: (PF-703) The horizontal conveyance sensor /4 (PS34) does not turn ON within a specified period of time after the horizontal conveyance sensor /3 (PS33) turns ON. |
|
J-1814 |
During operation: (PF-703) The horizontal conveyance sensor /5 (PS35) does not turn ON within a specified period of time after the horizontal conveyance sensor /4 (PS34) turns ON. |
|
J-1815 |
During operation: (PF-703) The horizontal conveyance sensor /1 (PS17) does not turn ON within a specified period of time after the horizontal conveyance sensor /5 (PS35) turns ON. |
Paper feed conveyance (PFU1) |
J-1851 |
When idling: (PF-703/706) The intermediate sensor /Up (PS16) turns ON while in idling. |
|
J-1852 |
When idling: (PF-703/706) The loop sensor /1 (PS17) turns ON while in idling. |
|
J-1853 |
When idling: (PF-703/706) The loop sensor /2 (PS19) turns ON while in idling. |
|
J-1854 |
When idling: (PF-703/706) The intermediate sensor /Lw (PS22) turns ON while in idling. |
|
J-1855 |
When idling: (PF-703/706) The loop sensor /3 (PS23) turns ON while in idling. |
|
J-1856 |
When idling: (PF-703/706) The PF exit conveyance sensor (PS24) turns ON while in idling. |
Horizontal conveyance (PFU1) |
J-1860 |
When idling: (PF-703) The horizontal conveyance sensor /1 (PS31) turns ON while in idling. |
|
J-1861 |
When idling: (PF-703) The horizontal conveyance sensor /2 (PS32) turns ON while in idling. |
|
J-1862 |
When idling: (PF-703) The horizontal conveyance sensor /3 (PS33) turns ON while in idling. |
|
J-1863 |
When idling: (PF-703) The horizontal conveyance sensor /4 (PS34) turns ON while in idling. |
|
J-1864 |
When idling: (PF-703) The horizontal conveyance sensor /5 (PS35) turns ON while in idling. |
Conveyance |
J-1901 |
During operation: The main body vertical conveyance door is opened while in printing. |
PF |
J-1902 |
During operation: The PFU1 front door is opened while in printing. |
LU |
J-1902 |
During operation: The LU jam door is opened while in printing. Or, the upper cover is opened while in LU operating. |
PF |
J-1903 |
During operation: The PFU2 front door is opened while in printing. |
|
J-1904 |
During operation: The PI-PFU front door is opened while in printing. |
Fusing/ paper exit |
J-2101 |
During operation: While in the print sequence, the JAM sensor board (JAMB) detects paper at a prescribed timing. |
|
J-2151 |
When idling: While in idling, the JAM sensor board (JAMB) detects paper at a prescribed timing. |
|
J-3101 |
During operation: The paper leading edge sensor (PS41) does not turn ON within a specified period of time after the registration motor (M17) turns ON. |
|
J-3102 |
During operation: The fusing exit sensor (PS22) does not turn ON within a specified period of time after the paper leading edge sensor (PS41) turns ON. |
|
J-3103 |
During operation: PS41 does not turn OFF even after 1.1 times of the conveyance time of the transfer paper length elapses after the paper leading edge sensor (PS41) turns ON. |
|
J-3110 |
During operation: Printer control abnormality |
|
J-3111 |
During operation: 1.0% or 0.5% of the skew is detected by the paper skew sensor /Fr (PS65), the paper skew sensor /Rr (PS66).(PRO 951 is unimplemented) |
|
J-3112 |
During operation: Centering of 5mm or more is detected by the centering sensor (PS4) |
|
J-3201 |
During operation: The de-curler entrance solenoid (PS23) does not turn ON within a specified period of time after the fusing exit sensor (PS22) turns ON. |
|
J-3202 |
During operation: While in the straight paper exit, the paper exit sensor (PS3) does not turn ON within a specified period of time after the decurler entrance solenoid (PS23) turns ON. |
|
J-3203 |
During operation: ADU accelerate sensor (PS49) does not turn ON within a specified period of time after the fusing exit sensor (PS22) turns ON. |
|
J-3204 |
During operation: The reverse sensor /1 (PS48) does not turn ON within a specified period of time after the ADU accelerate sensor (PS49) turns ON. |
|
J-3205 |
During operation: The PS48 does not turn ON again within a specified period of time after the reverse sensor /1 (PS48) turns ON. |
|
J-3206 |
During operation: The de-curler entrance solenoid (PS23) does not turn ON within a specified period of time after the reverse sensor /1 (PS48) turns ON. |
|
J-3207 |
During operation: While in the reverse paper exit, the paper exit sensor (PS3) does not turn ON within a specified period of time after the decurler entrance solenoid (PS23) turns ON. |
|
J-3208 |
During operation: The PS3 does not turn OFF again within a specified period of time after the paper exit sensor (PS3) turns ON. |
|
J-3251 |
When idling: The fusing exit sensor (PS22) turns ON while in idling. |
|
J-3252 |
When idling: The paper exit sensor (PS3) turns ON while in idling. |
|
J-3253 |
When idling: The ADU accelerate sensor (PS49) turns ON while in idling. |
|
J-3254 |
When idling: The ADU reverse paper exit sensor (PS50) turns ON while in idling. |
|
J-3255 |
When idling: The fusing jam sensor (PS38) turns ON while in idling. |
|
J-3256 |
When idling: The reverse sensor /1 (PS48) turns ON while in idling. |
|
J-3257 |
When idling: The reverse sensor /2 (PS47) turns ON while in idling. |
|
J-3258 |
When idling: The de-curler entrance sensor (PS23) turns ON while in idling. |
External |
J-5101 |
During operation: The front door/R, /L of the main body was opened while printing. |
|
J-5102 |
During operation: The waste toner BOX got into the unset status while in the print. |
DF |
J-6101 |
During operation: The DF open-close sensor (PS301) turns ON while in operation. |
|
J-6102 |
During operation: The cover open-close switch (MS301) turns ON while in operation. |
|
J-6201 |
During operation: The original registration sensor /Lt (PS306) does not turn OFF within a specified period of time after the pre-feed start. |
|
J-6202 |
During operation: The original conveyance sensor (PS308) does not turn ON within a specified period of time after the pre-feed start of the front side of the double-sided original (including the single-sided original). |
|
J-6203 |
During operation: The original conveyance sensor (PS308) does not turn ON within a specified period of time after the pre-feed start of the back side of the double-sided original. |
|
J-6204 |
During operation: While in the forward rotation of the original conveyance motor (M302), the original conveyance sensor (PS308) does not turn OFF within a specified period of time after it turns ON. |
|
J-6205 |
During operation: While in the reverse rotation of the original conveyance motor (M302), the original conveyance sensor (PS308) does not turn OFF within a specified period of time after it turns ON. |
|
J-6206 |
During operation: When entering a large-size double-sided original in the reverse section, the original reverse sensor (PS309) does not turn ON within a specified period of time after the original conveyance sensor (PS308) turns ON. |
|
J-6207 |
During operation: When exiting a large-size single-sided original, the original exit sensor /Lt (PS307) does not turn ON within a specified period of time after the original conveyance sensor (PS308) turns ON. |
|
J-6208 |
During operation: When exiting a large-size double-sided original, the original exit sensor /Lt (PS307) does not turn ON within a specified period of time after the original reverse sensor (PS309) turns ON. |
|
J-6209 |
During operation: When exiting a large-size single-sided original, the original exit sensor /Lt (PS307) does not turn OFF within a specified period of time after it turns ON. |
|
J-6210 |
During operation: When exiting a large-size double-sided original, the original exit sensor /Lt (PS307) does not turn OFF within a specified period of time after it turns ON. |
|
J-6301 |
During operation: When outputting a large-size double-sided original from the reverse section, the original reverse sensor (PS309) does not turn ON. |
|
J-6302 |
During operation: When entering a large-size double-sided original into the reverse section, the original reverse sensor (PS309) does not turn OFF within a specified period of time after it turns ON. |
|
J-6303 |
During operation: When outputting a large-size double-sided original from the reverse section, the original reverse sensor (PS309) does not turn OFF within a specified period of time after it turns ON. |
|
J-6304 |
During operation: When exiting a small-size single-sided original, the original exit sensor /Rt (PS314) does not turn ON within a specified period of time after the original reverse sensor (PS309) turns ON. |
|
J-6305 |
During operation: When exiting a small-size double-sided original, the original exit sensor /Rt (PS314) does not turn OFF within a specified period of time after the original reverse-exit sensor (PS313) turns ON. |
|
J-6306 |
During operation: When exiting a small-size single-sided original, the original exit sensor /Rt (PS314) does not turn OFF within a specified period of time after it turns ON. |
|
J-6307 |
During operation: When exiting a small-size double-sided original, the original exit sensor /Rt (PS314) does not turn OFF within a specified period of time after it turns ON. |
|
J-6308 |
During operation: When entering a small-size double-sided original in the reverse section, the original reverse-exit sensor (PS313) does not turn ON within a specified period of time after the original conveyance sensor (PS308) turns ON. |
|
J-6309 |
During operation: When outputting a small-size double-sided original in the reverse section, the original reverse-exit sensor (PS313) does not turn ON within a specified period of time after the original conveyance sensor (PS308) turns ON. |
|
J-6310 |
During operation: When entering a small-size double-sided original into the reverse section, the original reverse-exit sensor (PS313) does not turn OFF within a specified period of time after it turns ON. |
|
J-6311 |
During operation: When outputting a small-size double-sided original into the reverse section, the original reverse-exit sensor (PS313) does not turn OFF within a specified period of time after it turns ON. |
|
J-6501 |
When idling: The original registration sensor /Lt (PS306) turns ON while in idling. |
|
J-6502 |
When idling: The original conveyance sensor (PS308) turns ON while in idling. |
|
J-6504 |
When idling: The original reverse sensor (PS309) turns ON while in idling. |
|
J-6508 |
When idling: The original exit sensor /Lt (PS307) turns ON while in idling. |
|
J-6510 |
When idling: The original reverse-exit sensor (PS313) turns ON while in idling. |
|
J-6520 |
When idling: The original exit sensor /Rt (PS314) turns ON while in idling. |
|
J-6540 |
When idling: The reverse jam sensor (PS304) turns ON while in idling. |
|
J-6580 |
When idling: The original registration sensor /Rt (PS318) turns ON while in idling. (DF-615 only) |
FS |
J-7101 |
During operation: The FS front door open jam. The door switch (MS1) turns OFF while in printing. |
RU |
J-7102 |
During operation: (RU-510) The RU front door open jam. The interlock switch (MS1) turns OFF while in the print. |
LS (1st tandem) |
J-7103 |
During operation: The LS front door open jam. The door switch (MS1) turns OFF while in printing. |
LS (2nd tandem) |
J-7104 |
During operation: The LS front door open jam. The door switch (MS1) turns OFF while in printing. |
FD |
J-7105 |
During operation: The FD front door open jam. The front door switch (MS1) turns OFF while in the print. |
SD-506 |
J-7107 |
During operation: The SD front door/Rt open jam or the SD front door/Lt open jam. During printing, either the SD front door switch /Rt (MS1) or /Lt (MS2) turns OFF. |
PB |
J-7108 |
During operation: The PB front door open jam. During printing, the front door switch (SW2), booklet door switch (SW3), upper door switch (SW1), and relay conveyance section door switch (MS3) turn OFF. |
GP-501 |
J-7109 |
During operation: The GP front door open jam. The door switch turns OFF while in the print. |
RU |
J-7110 |
During operation: (RU-509) The RU front door open jam. The door switch (SW1) turns OFF while in printing. |
GP-502 |
J-7111 |
During operation: The GP front door open jam. The line Interrupt Interlock switch turns OFF while in the print. |
LS (3rd tandem) |
J-7112 |
During operation: The LS front door open jam. The door switch (MS1) turns OFF while in printing. |
FS |
J-7216 |
During operation: The FNS entrance sensor (PS1) does not turn ON within a specified period of time after the paper exit sensor of the previous option turns ON. |
|
J-7217 |
During operation: The main tray paper exit sensor (PS10) does not turn ON within a specified period of time after the FNS entrance sensor (PS1) turns ON. |
|
J-7218 |
During operation: The paper overlap sensor /1 (PS32) does not turn ON within a specified period of time after the FNS entrance sensor (PS1) turns ON. |
|
J-7220 |
During operation: While in stapling a small-size paper, the main tray paper exit sensor (PS10) does not turn ON within a specified period of time after the paper exit operation starts. |
|
J-7221 |
During operation: While in stapling a large-size paper, the main tray paper exit sensor (PS10) does not turn OFF within a specified period of time after the paper exit operation starts. |
|
J-7222 |
During operation: While in exiting paper in the sub tray, the sub tray exit sensor (PS8) does not turn ON within a specified period of time after the paper exit sensor of the previous option turns ON. |
|
J-7223 |
During operation: While in exiting paper in the sub tray, PS1 does not turn OFF within a specified period of time after the sub tray exit sensor (PS8) turns ON. |
|
J-7224 |
During operation: The stacker rear alignment sensor (PS44) does not turn ON within a specified period of time after the exit of paper bundle is completed.Or, PS44 turns OFF before a specified time since the small size paper alignment motor (M18) starts to excite when the standby position of exiting the paper bundle for the FD alignment plate is being moved. |
SD-510 |
J-7225 |
During operation: While in the tri-folding mode, the folding exit sensor (PS113) does not turn ON within a specified period of time after the folding is completed. |
|
J-7226 |
During operation: PS113 does not turn OFF within a specified period of time after the folding exit sensor (PS113) turns ON. |
FS |
J-7227 |
During operation: The paper overlap sensor /2 (PS33) does not turn ON within a specified period of time after the stacker entrance motor (M5) starts reverse rotation. |
|
J-7228 |
During operation: PS32 does not turn OFF within a specified period of time after the paper overlap sensor /1 (PS32) turns ON. |
|
J-7229 |
During operation: The main tray paper exit sensor (PS10) does not turn OFF within a specified period of time after the FNS entrance sensor (PS1) turns OFF. |
|
J-7230 |
During operation: The main tray paper exit sensor (PS10) does not turn ON within a specified period of time after stapling a small- size paper starts. |
|
J-7231 |
During operation: The paper overlap sensor /2 (PS33) does not turn OFF within a specified period of time after the stacker entrance motor (M5) starts forward rotation. Paper which is 253mm or more in the sub scan direction is not target. |
PI |
J-7235 |
During operation: The paper passage sensor / Lw (PS206) does not turn ON within a specified period of time after the conveyance clutch /Lw (CL202) turns ON. Or, the paper passage sensor /Lw (PS206) does not turn ON within a specified period of time after the paper passage sensor /Up (PS201) turns ON. |
FS |
J-7236 |
During operation: The paper overlap sensor /2 (PS33) does not turn ON within a specified period of time after the FNS entrance sensor (PS1) turns ON. |
SD-510 |
J-7237 |
During operation: The SD entrance sensor (PS102) does not turn ON within a specified period of time after the paper overlap sensor /2 (PS33) turns ON. |
ZU |
J-7238 |
During operation: The leading/trailing/side edge sensors of the paper edge sensor board (PESB) do not turn ON within a specified period of time after the main body paper exit sensor (PS3) turns ON. |
|
J-7239 |
During operation: The leading/trailing/side edge sensors of the paper edge sensor board (PESB) do not turn OFF within a specified period of time after they turn ON. |
|
J-7240 |
During operation: The conveyance sensor (PS601) does not turn ON within a specified period of time after the leading/trailing/side edge sensors of the paper edge sensor board (PESB) turn ON. |
|
J-7241 |
During operation: The conveyance sensor (PS601) does not switch from ON to OFF within a specified period of time after the Z-fold mode starts the 2nd folding. |
|
J-7242 |
During operation: The conveyance sensor (PS601) does not switch from ON to OFF within a specified period of time after the Z-fold mode finishes the 2nd folding. |
PK |
J-7243 |
During operation: The paper size sensor (PS305) does not detect the paper edge even after a specified period of time has passed after the punch shift motor (M302) turns ON. Or, the punch home sensor /1 (PS301) or /2 (PS307) does not turn ON even after a specified period of time has passed after the punch motor (M301) turns ON. |
ZU |
J-7244 |
During operation: The exit sensor (PS609) does not turn ON within a specified period of time after the leading/trailing/side edge sensors of the paper edge sensor board (PESB) turn ON. |
|
J-7245 |
During operation: The exit sensor (PS609) does not turn ON within a specified period of time after the main body paper exit sensor (PS3) turns ON. |
|
J-7246 |
During operation: The exit sensor (PS609) does not turn OFF within a specified period of time after the exit sensor (PS609) turns ON. |
|
J-7247 |
During operation: The paper remains in the Z- fold unit within a specified period of time after the main body transmits the operation stop signal to the Z-fold unit. |
SD-510 |
J-7248 |
During operation: The paper passage sensor / Up (PS201) does not turn ON within a specified period of time after the pick-up solenoid /Up (SD201) turns ON. |
PI |
J-7249 |
During operation: The paper passage sensor / Up (PS201) does not turn ON within a specified period of time after the pick-up solenoid /Up (SD201) turns ON. |
|
J-7250 |
During operation: The FNS entrance sensor (PS1) does not turn ON within a specified period of time after the paper passage sensor /Up (PS201) turns ON. |
|
J-7251 |
During operation: The FNS entrance sensor (PS1) does not turn ON within a specified period of time after the paper passage sensor /Lw (PS206) turns ON. |
ZU |
J-7260 |
During operation: The certain side edge sensor in the paper edge sensor board (PESB) does not turn ON within a specified period of time after the paper turns OFF leading/trailing/side edge sensors of the paper edge sensor board (PESB). Or, the punch home sensor (PS606) does not turn ON within a specified period of time after the punch clutch (CL601) turns ON. |
|
J-7261 |
During operation: The saddle entrance sensor (PS102) does not turn ON within a specified period of time after the paper overlap sensor /2 (PS33) turns ON. |
|
J-7262 |
During operation: The exit sensor (PS609) does not turn ON within a specified period of time after the conveyance sensor (PS601) turns ON. |
|
J-7264 |
During operation: The conveyance sensor (PS601) does not turn ON within a specified period of time after the leading/trailing/side edge sensors of the paper edge sensor board (PESB) turn ON. |
SD-510 |
J-7265 |
During operation: While in the tri-folding mode, the 2nd folding sensor (PS112) does not turn ON within a specified period of time after 1st folding starts. |
|
J-7266 |
During operation: The SD entrance sensor (PS102) does not turn OFF within a specified period of time after it turns ON. |
|
J-7272 |
During operation: Stapler bucking, empty staple. |
FS |
J-7281 |
During operation: The stapler home sensor (PS40) does not turn ON within a specified period of time after the stapler motor (M31) turns ON. |
|
J-7290 |
During operation: FS or SD does not stop within a specified period of time after the operation stop signal is transmitted from the main body to the FS or SD. |
|
J-7301 |
When idling: The main tray paper exit sensor (PS10) turns ON while in idling. |
|
J-7302 |
When idling: The paper overlap sensor /1 (PS32) turns ON while in idling. |
|
J-7303 |
When idling: The stacker upper sensor (PS43) turns ON while in idling. |
|
J-7304 |
When idling: The paper overlap sensor /2 (PS33) turns ON while in idling. |
|
J-7305 |
When idling: The FNS entrance sensor (PS1) turns ON while in idling. |
|
J-7307 |
When idling: The sub tray exit sensor (PS8) turns ON while in idling. |
|
J-7308 |
When idling: The stacker empty sensor (PS28) turns ON while in idling. |
SD-510 |
J-7309 |
When idling: The stacker empty sensor (PS101) turns ON while in idling. |
|
J-7310 |
When idling: The folding exit sensor (PS113) turns ON while in idling. |
PI |
J-7314 |
When idling: The paper passage sensor /Lw (PS206) turns ON while in idling. |
FS |
J-7316 |
When idling: The paper overlap sensor /3 (PS5) turns ON while in idling. |
PI |
J-7317 |
When idling: The paper passage sensor /Up (PS201) turns ON while in idling. |
SD-510 |
J-7318 |
When idling: The SD entrance sensor (PS102) turns ON while in idling. |
|
J-7319 |
When idling: The 2nd folding sensor (PS112) turns ON while in idling. |
GP-502 |
J-7320 |
When idling: The bypass direct entry sensor turns ON while in idling. |
|
J-7321 |
When idling: The bypass direct exit sensor turns ON while in idling. |
|
J-7322 |
When idling: The tall vertical entry sensor turns ON while in idling. |
|
J-7323 |
When idling: The punch sensor turns ON while in idling. |
|
J-7324 |
When idling: The pullback sensor turns ON while in idling. |
|
J-7325 |
When idling: The paper present sensor (below tray) turns ON while in idling. |
|
J-7326 |
When idling: The jam sensor at the document drawer turns ON while in idling. |
ZU |
J-7330 |
When idling: One of these sensors turn ON while in idling. Conveyance sensor(PS601) 1st folding stopper home sensor (PS603) 2nd folding stopper home sensor (PS604) Punch shift home sensor (PS605) - Exit sensor (PS609) |
RU |
J-7340 |
When idling: (RU-510) Either of the entrance sensor (PS1), the entrance jam sensor (PS6), or the gate home sensor (PS7) turns ON while in idling. |
|
J-7341 |
When idling: (RU-510) Either of the stacker jam sensor (PS5) or the stack switch home sensor (PS8) turns ON while in idling. |
|
J-7342 |
When idling: (RU-510) The paper exit sensor (PS2) turns ON while in idling. |
LS @rd tandem) |
J-7346 |
During operation: The entrance sensor (PS4) turns ON while in idling. |
|
J-7347 |
When idling: The sub tray paper exit sensor (PS10) turns ON while in idling. |
|
J-7348 |
When idling: Either of the conveyance sensor /1 (PS7), /2 (PS16), or /3 (PS17) turns ON while in idling. |
|
J^49 |
When idling: The coupling exit sensor (PS18) turns ON while in idling. |
LS (1st tandem) |
J-7350 |
During operation: The entrance sensor (PS4) turns ON while in idling. |
|
J-7351 |
When idling: The sub tray paper exit sensor (PS10) turns ON while in idling. |
|
J-7352 |
When idling: Either of the conveyance sensor /1 (PS7), /2 (PS16), or /3 (PS17) turns ON while in idling. |
|
J-7353 |
When idling: The coupling exit sensor (PS18) turns ON while in idling. |
LS (2nd tandem) |
J-7354 |
During operation: The entrance sensor (PS4) turns ON while in idling. |
|
J-7355 |
When idling: The sub tray paper exit sensor (PS10) turns ON while in idling. |
|
J-7356 |
When idling: Either of the conveyance sensor /1 (PS7), /2 (PS16), or /3 (PS17) turns ON while in idling. |
|
J-7357 |
When idling: The coupling exit sensor (PS18) turns ON while in idling. |
FD |
J-7358 |
When idling: Either of the FD entrance sensor (PS1), the punch conveyance sensor (PS5), or the punch registration sensor (PS6) turns ON while in idling. |
|
J-7359 |
When idling: Either of the intermediate conveyance sensor (PS13), the sub tray paper exit sensor (PS16), or the main tray paper exit sensor (PS18) turns ON while in idling. |
|
J-7360 |
When idling: Either of the 1st folding conveyance sensor (PS51), the 2nd folding conveyance sensor (PS53), the 3rd folding conveyance sensor (PS54), the S size conveyance sensor (PS58), the folding entrance sensor (PS52), or the folding exit sensor (PS2) turns ON while in idling. |
|
J-7361 |
When idling: Either of the PI conveyance sensor /Up (PS31), the PI conveyance sensor / Lw (PS37), or the PI exit sensor (PS4) turns ON while in idling. |
RU |
J-7365 |
When idling: (RU-509) The entrance sensor (PS1) turns ON while in idling. |
|
J-7366 |
When idling: (RU-509) Either of the de-curler entrance sensor (PS2) or the humidification section entrance sensor (PS7) turns ON while in idling. |
|
J-7367 |
When idling: (RU-509) Either of the color density detection timing sensor (PS3), paper exit conveyance sensor (PS4) or paper exit sensor (PS12) turns ON while in idling. |
SD-506 |
J-7368 |
When idling: The entrance sensor (PS1) turns ON while in idling. |
|
J-7369 |
When idling: Either of the horizontal conveyance sensor /1 (PS2), the horizontal conveyance sensor /2 (PS3), or the sub tray exit sensor (PS11) turns ON while in idling. |
|
J-7370 |
When idling: The horizontal conveyance exit sensor (PS4) turns ON while in idling. |
|
J-7371 |
When idling: Either of the right angle conveyance sensor /1 (PS5) or the right angle conveyance sensor /2 (PS6) turns ON while in idling. |
|
J-7372 |
When idling: Either of the folding sensor /1 (PS7), the folding passage sensor (PS8), the trifolding exit sensor (PS9), or the folding sensor / 2 (PS44) turns ON while in idling. |
|
J-7373 |
When idling: The saddle stitching paper sensor (PS13) turns ON while in idling. |
|
J-7374 |
When idling: Either of the bundle sensor /1 (PS14), /2 (PS15), /4 (PS54), or the bundle exit sensor /2 (PS57) turns ON while in idling. |
PB |
J-7380 |
When idling: Either of the entrance sensor (PS1), the SC entrance sensor (PS2), the cover paper entrance sensor (PS3), or the sub tray paper exit sensor (PS4) turns ON while in idling. |
|
J-7381 |
When idling: The SC paper detection sensor (PS16) turns ON while in idling. |
|
J-7382 |
When idling: The clamp paper sensor (PS28) turns ON while in idling. |
|
J-7383 |
When idling: Either of the cover paper switchback sensor (PS44), the cover paper sensor /Rt (PS45), or the cover paper sensor /Lt (PS46) turns ON while in idling. |
|
J-7384 |
When idling: The book end fence sensor (PS61) turns ON while in idling. |
|
J-7385 |
When idling: The cover paper conveyance sensors /1 (PS75), /2 (PS76), /3 (PS77), / 4(PS78), and /5 (PS79) turn ON while in idling. |
|
J-7386 |
When idling: The relay conveyance entrance sensor (PS93), the relay conveyance intermediate sensor (PS91) and the relay conveyance exit sensor (PS94) turn ON during idling. |
GP-501 |
J-7390 |
When idling: The enter sensor (S1) turns ON while in idling. |
|
J-7391 |
When idling: The stepper 1 speed sensor (S2) turns ON while in idling. |
|
J-7392 |
When idling: The bypass sensor (S8) turns ON while in idling. |
|
J-7393 |
When idling: The exit sensor (S7) turns ON while in idling. |
|
J-7394 |
When idling: The punch flag sensor (S9) turns ON while in idling. |
|
J-7395 |
When idling: The u-channel sensor (S4) turns ON while in idling. |
|
J-7396 |
When idling: The backstop sensor (S5) turns ON while in idling. |
|
J-7397 |
When idling: The stepper 2 speed sensor (S6) turns ON while in idling. |
LS (1st tandem) |
J-7401 |
During operation: The entrance sensor (PS4) does not turn ON within a specified period of time after the main body paper exit sensor (PS3) turns ON. |
|
J-7402 |
During operation: The entrance sensor (PS4) does not turn OFF within a specified period of time after it turns ON. |
|
J-7403 |
During operation: The sub tray exit sensor (PS10) does not turn ON within a specified period of time after the entrance sensor (PS4) turns ON. |
|
J-7404 |
During operation: The sub tray paper exit sensor (PS10) does not turn OFF within a specified period of time after it turns ON. |
|
J-7405 |
During operation: The conveyance sensor /1 (PS7) does not turn ON within a specified period of time after the entrance sensor (PS4) turns ON. |
|
J-7406 |
During operation: The conveyance sensor /1 (PS7) does not turn OFF within a specified period of time after it turns ON. |
|
J-7407 |
During operation: The conveyance sensor /2 (PS16) does not turn ON within a specified period of time after the conveyance sensor /1 (PS7) turns ON. |
|
J-7408 |
During operation: The conveyance sensor /2 (PS16) does not turn OFF within a specified period of time after it turns ON. |
|
J-7409 |
During operation: The conveyance sensor /3 (PS17) does not turn ON within a specified period of time after the conveyance sensor /2 (PS16) turns ON. |
|
J-7410 |
During operation: The conveyance sensor /3 (PS17) does not turn OFF within a specified period of time after it turns ON. |
|
J-7411 |
During operation: The coupling exit sensor (PS18) does not turn ON within a specified period of time after the conveyance sensor /3 (PS17) turns ON. |
|
J-7412 |
During operation: The coupling exit sensor (PS18) does not turn OFF within a specified period of time after it turns ON. |
LS (2nd tandem) |
J-7431 |
During operation: The entrance sensor (PS4) does not turn ON within a specified period of time after the main body paper exit sensor (PS3) turns ON. |
|
J-7432 |
During operation: The entrance sensor (PS4) does not turn OFF within a specified period of time after it turns ON. |
|
J-7433 |
During operation: The sub tray exit sensor (PS10) does not turn ON within a specified period of time after the entrance sensor (PS4) turns ON. |
|
J-7434 |
During operation: The sub tray paper exit sensor (PS10) does not turn OFF within a specified period of time after it turns ON. |
|
J-7435 |
During operation: The conveyance sensor /1 (PS7) does not turn ON within a specified period of time after the entrance sensor (PS4) turns ON. |
|
J-7436 |
During operation: The conveyance sensor /1 (PS7) does not turn OFF within a specified period of time after it turns ON. |
|
J-7437 |
During operation: The conveyance sensor /2 (PS16) does not turn ON within a specified period of time after the conveyance sensor /1 (PS7) turns ON. |
|
J-7438 |
During operation: The conveyance sensor /2 (PS16) does not turn OFF within a specified period of time after it turns ON. |
|
J-7439 |
During operation: The conveyance sensor /3 (PS17) does not turn ON within a specified period of time after the conveyance sensor /2 (PS16) turns ON. |
|
J-7440 |
During operation: The conveyance sensor /3 (PS17) does not turn OFF within a specified period of time after it turns ON. |
|
J-7441 |
During operation: The coupling exit sensor (PS18) does not turn ON within a specified period of time after the conveyance sensor /3 (PS17) turns ON. |
|
J-7442 |
During operation: The coupling exit sensor (PS18) does not turn OFF within a specified period of time after it turns ON. |
LS (3rd tandem) |
J-7461 |
During operation: The entrance sensor (PS4) does not turn ON within a specified period of time after the main body paper exit sensor (PS3) turns ON. |
|
J-7462 |
During operation: The entrance sensor (PS4) does not turn OFF within a specified period of time after it turns ON. |
|
J-7463 |
During operation: The sub tray exit sensor (PS10) does not turn ON within a specified period of time after the entrance sensor (PS4) turns ON. |
|
J-7464 |
During operation: The sub tray paper exit sensor (PS10) does not turn OFF within a specified period of time after it turns ON. |
|
J-7465 |
During operation: The conveyance sensor /1 (PS7) does not turn ON within a specified period of time after the entrance sensor (PS4) turns ON. |
|
J-7466 |
During operation: The conveyance sensor /1 (PS7) does not turn OFF within a specified period of time after it turns ON. |
|
J-7467 |
During operation: The conveyance sensor /2 (PS16) does not turn ON within a specified period of time after the conveyance sensor /1 (PS7) turns ON. |
|
J-7468 |
During operation: The conveyance sensor /2 (PS16) does not turn OFF within a specified period of time after it turns ON. |
|
J-7469 |
During operation: The conveyance sensor /3 (PS17) does not turn ON within a specified period of time after the conveyance sensor /2 (PS16) turns ON. |
|
J-7470 |
During operation: The conveyance sensor /3 (PS17) does not turn OFF within a specified period of time after it turns ON. |
|
J-7471 |
During operation: The coupling exit sensor (PS18) does not turn ON within a specified period of time after the conveyance sensor /3 (PS17) turns ON. |
|
J-7472 |
During operation: The coupling exit sensor (PS18) does not turn OFF within a specified period of time after it turns ON. |
FD |
J-7501 |
During operation: The FD entrance sensor (PS1) does not turn ON within a specified period of time after the main body paper exit sensor (PS3) turns ON. |
|
J-7502 |
During operation: The intermediate conveyance sensor (PS13) does not turn ON within a specified period of time after the FD entrance sensor (PS1) turns ON. |
|
J-7503 |
During operation: The main tray exit sensor (PS18) does not turn ON within a specified period of time after the intermediate conveyance sensor (PS13) turns ON. |
|
J-7504 |
During operation: The main tray exit sensor (PS18) does not turn OFF within a specified period of time after it turns ON. |
|
J-7505 |
During operation: The sub tray paper exit sensor (PS16) does not turn ON within a specified period of time after the intermediate conveyance sensor (PS13) turns ON. |
|
J-7506 |
During operation: The sub tray paper exit sensor (PS16) does not turn OFF within a specified period of time after it turns ON. |
|
J-7507 |
During operation: The punch conveyance sensor (PS5) does not turn ON within a specified period of time after the FD entrance sensor (PS1) turns ON. |
|
J-7508 |
During operation: The 3rd folding conveyance sensor (PS54) does not turn ON within a specified period of time after the punch conveyance sensor (PS5) turns ON. |
|
J-7509 |
During operation: The punch registration sensor (PS6) does not turn ON within a specified period of time after the punch conveyance sensor (PS5) turns ON. |
|
J-7510 |
During operation: The 1st folding conveyance sensor (PS51) does not turn ON within a specified period of time after the punch registration sensor (PS6) turns ON. |
|
J-7511 |
During operation: The 3rd folding conveyance sensor (PS54) does not turn ON within a specified period of time after the 1st folding conveyance sensor (PS51) turns ON. |
|
J-7512 |
During operation: The intermediate conveyance sensor (PS13) does not turn ON within a specified period of time after the 3rd folding conveyance sensor (PS54) turns ON. |
|
J-7513 |
During operation: While in the folding operation, the 2nd folding conveyance sensor (PS53) does not turn ON within a specified period of time after the 1st folding motor (M4) starts to accelerate. |
|
J-7514 |
During operation: While in the folding operation, the 3rd folding conveyance sensor (PS54) does not turn ON within a specified period of time after the 1st folding motor (M4) starts to accelerate. |
|
J-7515 |
During operation: While in the folding operation, the 3rd folding conveyance sensor (PS54) does not turn ON within a specified period of time after the 2nd folding motor (M5) starts to accelerate. |
|
J-7516 |
During operation: While in the folding operation, the intermediate conveyance sensor (PS13) does not turn ON within a specified period of time after the 3rd folding motor (M6) starts to accelerate. |
|
J-7517 |
During operation: While in the folding operation, the 3rd folding conveyance sensor (PS54) does not turn ON within a specified period of time after the 2nd folding conveyance sensor (PS53) turns ON. |
|
J-7518 |
During operation: While in the folding operation, the intermediate conveyance sensor (PS13) does not turn ON within a specified period of time after the 3rd folding conveyance sensor (PS54) turns ON. |
|
J-7519 |
During operation: The PI conveyance sensor / Up (PS31) does not turn ON within a specified period of time after the PI pick-up solenoid /Up (SD13) turns ON. |
|
J-7520 |
During operation: The PI exit sensor (PS4) does not turn ON within a specified period of time after the PI conveyance sensor /Up (PS31) turns ON. |
|
J-7521 |
During operation: The PI conveyance sensor / Lw (PS37) does not turn ON within a specified period of time after the PI pick-up solenoid /Lw (SD14) turns ON. |
|
J-7522 |
During operation: The PI exit sensor (PS4) does not turn ON within a specified period of time after the PI conveyance sensor /Lw (PS37) turns ON. |
|
J-7523 |
During operation: The FD entrance sensor (PS1) does not turn ON within a specified period of time after the PI exit sensor (PS4) turns ON. |
|
J-7524 |
During operation: The PI multi feed is detected. |
RU |
J-7530 |
During operation: (RU-510) The entrance sensor (PS1) does not turn ON within a specified period of time after the main body paper exit sensor (PS3) turns ON. |
|
J-7531 |
During operation: (RU-510) While in the straight pass, the paper exit sensor (PS2) does not turn ON within a specified period of time after the entrance sensor (PS1) turns ON. |
|
J-7532 |
During operation: (RU-510) The entrance sensor (PS1) does not turn OFF within a specified period of time after it turns ON. |
|
J-7533 |
During operation: (RU-510) While in the reverse pass, the paper exit sensor (PS2) does not turn ON within a specified period of time after the entrance sensor (PS1) turns ON. |
|
J-7535 |
During operation: (RU-510) The paper exit sensor (PS2) does not turn OFF within a specified period of time after it turns ON. |
|
J-7550 |
During operation: (RU-509) The entrance sensor (PS1) does not turn ON within a specified period of time. |
|
J-7551 |
During operation: (RU-509) The de-curler entrance sensor (PS7) does not turn ON within a specified period of time. |
|
J-7552 |
During operation: (RU-509) The de-curler entrance sensor (PS2) does not turn ON within a specified period of time in the bypass path conveyance. |
|
J-7553 |
During operation: (RU-509) The de-curler entrance sensor (PS2) does not turn ON within a specified period of time in the lower path conveyance. |
|
J-7554 |
During operation: (RU-509) The color density detection timing sensor (PS3) does not turn ON within a specified period of time. |
|
J-7555 |
During operation: (RU-509) The paper exit sensor (PS12) does not turn ON within a specified period of time. |
|
J-7556 |
During operation: (RU-509) The paper exit sensor (PS12) does not turn OFF within a specified period of time. |
SD-506 |
J-7561 |
During operation: The entrance sensor (PS1) does not turn ON within a specified period of time after the main body paper exit sensor (PS3) turns ON. |
|
J-7562 |
During operation: The horizontal conveyance sensor /1 (PS2) does not turn ON within a specified period of time after the entrance sensor (PS1) turns ON. |
|
J-7563 |
During operation: The horizontal conveyance sensor /2 (PS3) does not turn ON within a specified period of time after the horizontal conveyance sensor /1 (PS2) turns ON. |
|
J-7564 |
During operation: The horizontal conveyance exit sensor (PS4) does not turn ON within a specified period of time after the horizontal conveyance sensor /2 (PS3) turns ON. |
|
J-7565 |
During operation: The horizontal conveyance exit sensor (PS4) does not turn OFF within a specified period of time after it turns ON. |
|
J-7566 |
During operation: The sub tray paper exit sensor (PS11) does not turn ON within a specified period of time after the horizontal conveyance sensor /1 (PS2) turns ON. |
|
J-7567 |
During operation: The sub tray paper exit sensor (PS11) does not turn OFF within a specified period of time after it turns ON. |
|
J-7568 |
During operation: The right angle conveyance sensor /2 (PS6) does not turn ON within a specified period of time after the right angle conveyance motor (M6) turns ON. |
|
J-7569 |
During operation: The folding sensor /1 (PS7) does not turn ON within a specified period of time after the folding entrance motor (M3) turns ON. |
|
J-7570 |
During operation: The saddle stitching paper sensor (PS13) does not turn ON within a specified period of time after the folding sub scan alignment exit motor (M8) turns ON. |
|
J-7571 |
During operation: The bundle sensor /1 (PS14) does not turn ON within a specified period of time after the bundle arm rotation motor (M22) turns ON. |
|
J-7572 |
During operation: The bundle sensor /2 (PS15) does not turn ON within a specified period of time after the bundle clip motor (M11) turns ON. |
|
J-7573 |
During operation: The bundle sensor /4 (PS54) does not turn ON within a specified period of time after the bundle sensor /2 (PS15) turns ON. |
|
J-7574 |
During operation: The entrance sensor (PS1) does not turn OFF within a specified period of time after it turns ON. |
|
J-7575 |
During operation: The right angle conveyance sensor /2 (PS6) does not turn OFF within a specified period of time after it turns ON. Or the folding entrance sensor (PS60) does not turn OFF within a specified period of time after it turns ON. |
|
J-7576 |
During operation: The folding sensor /2 (PS44) does not turn OFF within a specified period of time after it turns ON. |
|
J-7577 |
During operation: The bundle sensor /1 (PS14) does not turn OFF within a specified period of time after it turns ON. |
|
J-7578 |
During operation: The bundle sensor /2 (PS15) does not turn OFF within a specified period of time after it turns ON. |
|
J-7579 |
During operation: The folding passage sensor (PS8) does not turn ON within a specified period of time after the folding transfer motor (M4) turns ON. |
|
J-7580 |
During operation: The tri-folding exit sensor (PS9) does not turn ON within a specified period of time after the folding transfer motor (M4) turns ON. |
|
J-7581 |
During operation: The folding sub scan alignment exit motor (M8) does not turn OFF within a specified period of time after it turns ON. |
|
J-7582 |
During operation: The folding passage sensor (PS8) does not turn OFF within a specified period of time after it turns ON. |
|
J-7583 |
During operation: The tri-folding paper exit sensor (PS9) does not turn OFF within a specified period of time after it turns ON. |
|
J-7584 |
During operation: The trimming registration sensor (PS55) does not turn ON within a specified period of time after the bundle press movement motor (M17) turns ON. |
|
J-7585 |
During operation: The trimming registration sensor (PS55) does not turn OFF within a specified period of time after the bundle registration motor (M12) turns ON. |
GP-501 |
J-7590 |
During operation: The enter sensor (S1) does not turn OFF within a specified period of time after it turns ON. |
|
J-7591 |
During operation: The stepper 1 speed sensor (S2) does not turn OFF within a specified period of time after it turns ON. |
|
J-7592 |
During operation: The bypass sensor (S8) does not turn OFF within a specified period of time after it turns ON. |
|
J-7593 |
During operation: The exit sensor (S7) does not turn OFF within a specified period of time after it turns ON. |
|
J-7594 |
During operation: The punch flag sensor (S9) does not turn OFF within a specified period of time after it turns ON. |
|
J-7595 |
During operation: The u-channel sensor (S4) does not turn OFF within a specified period of time after it turns ON. |
|
J-7596 |
During operation: The backstop sensor (S5) does not turn OFF within a specified period of time after it turns ON. |
|
J-7597 |
During operation: The stepper 2 speed sensor (S6) does not turn OFF within a specified period of time after it turns ON. |
GP-502 |
J-7601 |
During operation: The bypass direct entry sensor does not turn ON within a specified period of time after the main body paper exit sensor (PS3) turns ON. |
|
J-7602 |
During operation: The bypass direct entry sensor does not turn OFF within a specified period of time after it turns ON. |
|
J-7603 |
During operation: The bypass direct exit sensor does not turn OFF within a specified period of time after it turns ON. |
|
J-7604 |
During operation: The tall vertical entry sensor does not turn OFF within a specified period of time after it turns ON. |
|
J-7605 |
During operation: The punch sensor does not turn OFF within a specified period of time after it turns ON. |
|
J-7606 |
During operation: The pullback sensor does not turn OFF within a specified period of time after it turns ON. |
|
J-7607 |
During operation: The jam sensor at the document drawer does not turn ON within a specified period of time after the main body paper exit sensor (PS3) turns ON. |
|
J-7608 |
During operation: The jam sensor at the document drawer does not turn OFF within a specified period of time after it turns ON. |
|
J-7611 |
During operation: The system trouble is detected in the bind mode. |
|
J-7612 |
During operation: The system trouble is detected in the bypass mode. |
PB |
J-7660 |
During operation: The entrance sensor (PS1) does not turn ON within a specified period of time after the main body paper exit sensor turns ON. |
|
J-7661 |
During operation: The SC entrance sensor (PS2) does not turn ON within a specified period of time after the entrance sensor (PS1) turns ON. |
|
J-7662 |
During operation: The SC entrance sensor (PS2) does not turn OFF within a specified period of time after it turns ON. |
|
J-7663 |
During operation: The cover paper entrance sensor (PS3) does not turn ON within a specified period of time after the main body paper exit sensor turns ON. |
|
J-7664 |
During operation: The sub tray paper exit sensor (PS4) does not turn ON within a specified period of time after the entrance sensor (PS1) turns ON. |
|
J-7665 |
During operation: The sub tray paper exit sensor (PS4) does not turn OFF within a specified period of time after it turns ON. |
|
J-7666 |
During operation: The SC paper detection sensor (PS16) does not turn ON within a specified period of time after the SC entrance sensor (PS2) turns ON. |
|
J-7667 |
During operation: The SC paper detection sensor (PS16) does not turn OFF within a specified period of time after it turns ON. |
|
J-7668 |
During operation: When conveying 2 sheets at a time, the SC paper detection sensor (PS16) does not turn ON within a specified period of time after the operation starts. |
|
J-7669 |
During operation: When conveying 2 sheets at a time, the SC paper detection sensor (PS16) does not turn OFF within a specified period of time after it turns ON. |
|
J-7670 |
During operation: The SC paper detection sensor (PS16) does not turn OFF within a specified period of time after the SC bundle conveyance motor (M17) turns ON. |
|
J-7671 |
During operation: The clamp paper sensor (PS28) does not turn OFF within a specified period of time after the clamp motor (M22) turns OFF. |
|
J-7674 |
During operation: The cover paper sensor /Rt (PS45) does not turn ON within a specified period of time after the cover paper feed clutch (CL71) turns ON. |
|
J-7675 |
During operation: The relay conveyance entrance sensor (PS93) does not turn ON within a specified period of time after the SC entrance sensor (PS2) turns ON. |
|
J-7676 |
During operation: When starting trimming of the cover paper fed from the PB, the cover paper switchback sensor (PS44) does not turn ON within a specified time period after the cover paper conveyance motor (M45) turns ON. |
|
J-7677 |
During operation: When finishing trimming of the cover paper fed from the PB, the cover paper switchback sensor (PS44) does not turn OFF within a specified time period after the cover paper conveyance motor (M45) turns ON. |
|
J-7678 |
During operation: When positioning the leading edge of the cover paper fed from the PB, the cover paper sensor/Lt (PS46) does not turn OFF within a specified time period after the cover paper conveyance motor (M45) turns ON. |
|
J-7679 |
During operation: When positioning the leading edge of the cover paper fed from the PB, the cover paper sensor/Lt (PS46) does not turn ON within a specified time period after the cover paper conveyance motor (M45) turns forward rotation ON. |
|
J-7680 |
During operation: When cover paper is fed from the main body, the cover paper sensor/Rt (PS45) does not turn ON within a specified time period after the cover paper entrance sensor (PS3) turns ON. |
|
J-7681 |
During operation: The relay conveyance intermediate sensor (PS91) does not turn ON within a specified period of time after the relay conveyance entrance sensor (PS93) turns ON. |
|
J-7682 |
During operation: When starting trimming of the cover paper fed from the main body, the cover paper switchback sensor (PS44) does not turn ON within a specified time period after the cover paper conveyance motor (M45) turns ON. |
|
J-7683 |
During operation: When finishing trimming of the cover paper fed from the main body, the cover paper switchback sensor (PS44) does not turn OFF within a specified time period after the cover paper conveyance motor (M45) turns ON. |
|
J-7684 |
During operation: When positioning the leading edge of the cover paper fed from the main body, the cover paper sensor/Lt (PS46) does not turn OFF within a specified time period after the cover paper conveyance motor (M45) turns ON. |
|
J-7685 |
During operation: When positioning the leading edge of the cover paper fed from the main body, the cover paper sensor/Lt (PS46) does not turn ON within a specified time period after the cover paper conveyance motor (M45) turns forward rotation ON. |
|
J-7686 |
During operation: The booklet end sensor (PS61) does not turn ON within a specified period of time after the booklet conveyance belt motor (M61) turns ON. |
|
J-7687 |
During operation: When loading first book, the booklet sensor /1 (PS66) does not turn ON within a specified period of time after the booklet conveyance belt up down motor (M63) turns ON. |
|
J-7688 |
During operation: When first row of book moves, the booklet sensor /2 (PS67) does not turn ON within a specified period of time after the booklet movement motor (M64) turns ON. |
|
J-7689 |
During operation: When feeding paper, the cover paper conveyance sensor /1 (PS75) does not turn ON within a specified period of time after the cover paper feed clutch (CL71) turns ON. |
|
J-7690 |
During operation: The cover paper conveyance sensor /2 (PS76) does not turn ON within a specified period of time after the cover paper conveyance sensor /1 (PS75) turns ON. |
|
J-7691 |
During operation: When refeeding paper, the cover paper conveyance sensor /3 (PS77) does not turn ON within a specified period of time after the cover paper feed clutch (CL71) turns ON. |
|
J-7692 |
During operation: The cover paper conveyance sensor /4 (PS78) does not turn ON within a specified period of time after the cover paper conveyance sensor /3 (PS77) turns ON. |
|
J-7693 |
During operation: The multi feed detection board /2 (MFDBR) turns OFF. |
|
J-7694 |
During operation: The relay conveyance exit sensor (PS94) does not turn ON within a specified period of time after the relay conveyance intermediate sensor (PS91) turns ON. |
|
J-7695 |
During operation: The relay conveyance exit sensor (PS94) does not turn OFF within a specified period of time after it turns ON. |
|
J-7696 |
During operation: The cover paper switchback sensor (PS44) does not turn ON within a specified period of time after the cover paper feed motor (M74) turns ON. |
|
J-7697 |
During operation: No paper is detected (paper has been removed) when restarting the job after recovery. |
|
J-7698 |
During operation: A cover paper has not been conveyed to the cover paper table section when clamping of inside pages is finished. |
Horizontal conveyance (PI-PFU) |
J-8101 |
During operation: (PF-703) The horizontal conveyance sensor /1 (PS31) does not turn ON within a specified period of time after the main body paper exit sensor (PS3) turns ON. |
|
J-8102 |
During operation: (PF-703) The horizontal conveyance sensor /2 (PS32) does not turn ON within a specified period of time after the horizontal conveyance sensor /1 (PS31) turns ON. |
|
J-8103 |
During operation: (PF-703) The horizontal conveyance sensor /3 (PS33) does not turn ON within a specified period of time after the horizontal conveyance sensor /2 (PS32) turns ON. |
|
J-8104 |
During operation: (PF-703) The horizontal conveyance sensor /4 (PS34) does not turn ON within a specified period of time after the horizontal conveyance sensor /3 (PS33) turns ON. |
|
J-8105 |
During operation: (PF-703) The horizontal conveyance sensor /5 (PS35) does not turn ON within a specified period of time after the horizontal conveyance sensor /4 (PS34) turns ON. |
|
J-8106 |
During operation: (PF-703) The horizontal conveyance sensor /1 (PS17) does not turn ON within a specified period of time after the horizontal conveyance sensor /5 (PS35) turns ON. |
Paper feed conveyance (PI-PFU) |
J-8107 |
During operation: PF-703 The multi feed detection boards and (MFDB and ) detect a double feed. |
Horizontal conveyance (PI-PFU) |
J-8109 |
During operation: PF-703 The PF exit conveyance sensor /2 (PS36) does not turn OFF within a specified period of time after it turns ON. |
Tray1 (PI- PFU) |
J-8111 |
During operation: PF-703 The paper feed sensor /1 (PS2) does not turn ON within a specified period of time after the paper feed clutch /1 (CL7) turns ON. |
|
J-8112 |
During operation: PF-703 The pre-registration sensor /1 (PS14) does not turn ON within a specified period of time after the paper feed clutch /1 (CL7) turns ON. |
|
J-8113 |
During operation: PF-703 The vertical conveyance sensor /1 (PS15) does not turn ON within a specified period of time after the pre-registration sensor /1 (PS14) turns ON. |
|
J-8114 |
During operation: PF-703 When the trailing edge of paper is passing through the vertical conveyance sensor /1 (PS15), the pre-registration sensor /1 (PS14) is turned ON by the succeeding paper. |
|
J-8115 |
During operation: PF-703 The paper suction sensor Fr/1 (PS25) and the paper suction sensor /Rr1(PS26) do not turn ON within a specified period of time from the rotation stabilization standby (3sec) after the paper suction fan /1 (FM13) and the paper suction fan / 2 (FM14) turn ON. |
Tray2 (PI- PFU) |
J-8121 |
During operation: PF-703 The paper feed sensor /2 (PS6) does not turn ON within a specified period of time after the paper feed clutch /2 (CL8) turns ON. |
|
J-8122 |
During operation: PF-703 The pre-registration sensor /2 (PS18) does not turn ON within a specified period of time after the paper feed clutch /2 (CL8) turns ON. |
|
J-8123 |
During operation: PF-703 When the trailing edge of paper is passing through the loop sensor /2 (PS19), the preregistration sensor /2 (PS18) is turned ON by the succeeding paper. |
|
J-8125 |
During operation: PF-703 The paper suction sensor Fr/3 (PS27) and the paper suction sensor /Rr2(PS28) do not turn ON within a specified period of time from the rotation stabilization standby (3sec) after the paper suction fan /3 (FM15) and the paper suction fan / 4 (FM16) turn ON. |
Tray3 (PI- PFU) |
J-8131 |
During operation: PF-703 The paper feed sensor /3 (PS10) does not turn ON within a specified period of time after the paper feed clutch /3 (CL9) turns ON. |
|
J-8132 |
During operation: PF-703 The pre-registration sensor /3 (PS20) does not turn ON within a specified period of time after the paper feed clutch /3 (CL9) turns ON. |
|
J-8133 |
During operation: PF-703 The vertical conveyance sensor /3 (PS21) does not turn ON within a specified period of time after the pre-registration sensor /3 (PS20) turns ON. |
|
J-8134 |
During operation: PF-703 When the trailing edge of paper is passing through the vertical conveyance sensor /3 (PS21), the pre-registration sensor /3 (PS20) is turned ON by the succeeding paper. |
|
J-8135 |
During operation: PF-703 The paper suction sensor Fr/3 (PS29) and the paper suction sensor Rr3(PS30) do not turn ON within a specified period of time from the rotation stabilization standby (3sec) after the paper suction fan /5 (FM17) and the paper suction fan / 6 (FM18) turn ON. |
Paper feed conveyance (PI-PFU) |
J-8141 |
During operation: PF-703 The intermediate sensor /Up (PS16) does not turn ON within a specified period of time after the vertical conveyance sensor /1 (PS15) turns ON. |
|
J-8142 |
During operation: PF-703 The loop sensor /1 (PS17) does not turn ON within a specified period of time after the intermediate sensor /Up (PS16) turns ON. |
|
J-8143 |
During operation: PF-703 The loop sensor /2 (PS19) does not turn ON within a specified period of time after the preregistration sensor /2 (PS18) turns ON. |
|
J-8144 |
During operation: PF-703 The intermediate sensor /Lw (PS22) does not turn ON within a specified period of time after the vertical conveyance sensor /3 (PS21) turns ON. |
|
J-8145 |
During operation: PF-703 The loop sensor /3 (PS23) does not turn ON within a specified period of time after the intermediate sensor /Lw (PS22) turns ON. |
|
J-8146 |
During operation: PF-703 The PF exit sensor /1 (PS24) does not turn ON within a specified period of time after the loop sensor /1 (PS17) turns ON. |
|
J-8147 |
During operation: PF-703 The PF exit sensor /1 (PS24) does not turn ON within a specified period of time after the loop sensor /2 (PS19) turns ON. |
|
J-8148 |
During operation: PF-703 The PF exit sensor /1 (PS24) does not turn ON within a specified period of time after the loop sensor /3 (PS23) turns ON. |
|
J-8149 |
During operation: PF-703 The PF exit conveyance sensor /2 (PS36) does not turn ON within a specified period of time after the PF exit conveyance sensor /1 (PS24) turns ON. |
Tray1 (PI- PFU) |
J-8151 |
When idling: PF-703 The pre-registration sensor /1 (PS14) turns ON while in idling. |
|
J-8152 |
When idling: PF-703 The vertical conveyance sensor /1 (PS15) turns ON while in idling. |
Tray2 (PI- PFU) |
J-8161 |
When idling: PF-703 The pre-registration sensor /2 (PS18) turns ON while in idling. |
Tray3 (PI- PFU) |
J-8171 |
When idling: PF-703 The pre-registration sensor /3 (PS20) turns ON while in idling. |
|
J-8172 |
When idling: PF-703 The vertical conveyance sensor /3 (PS21) turns ON while in idling. |
Paper feed conveyance (PI-PFU) |
J-8181 |
When idling: PF-703 The intermediate sensor /Up (PS16) turns ON while in idling. |
|
J-8182 |
When idling: PF-703 The loop sensor /1 (PS17) turns ON while in idling. |
|
J-8183 |
When idling: PF-703 The loop sensor /2 (PS19) turns ON while in idling. |
|
J-8184 |
When idling: PF-703 The intermediate sensor /Lw (PS22) turns ON while in idling. |
|
J-8185 |
When idling: PF-703 The loop sensor /3 (PS23) turns ON while in idling. |
|
J-8186 |
When idling: PF-703 The PF exit conveyance sensor /1 (PS24) turns ON while in idling. |
|
J-8187 |
When idling: PF-703 The PF exit conveyance sensor /2 (PS36) turns ON while in idling. |
Horizontal conveyance (PI-PFU) |
J-8191 |
When idling: (PF-703) The horizontal conveyance sensor /1 (PS31) turns ON while in idling. |
|
J-8192 |
When idling: (PF-703) The horizontal conveyance sensor /2 (PS32) turns ON while in idling. |
|
J-8193 |
When idling: (PF-703) The horizontal conveyance sensor /3 (PS33) turns ON while in idling. |
|
J-8194 |
When idling: (PF-703) The horizontal conveyance sensor /4 (PS34) turns ON while in idling. |
|
J-8195 |
When idling: (PF-703) The horizontal conveyance sensor /5 (PS35) turns ON while in idling. |
ADU |
J-9201 |
During operation: The ADU reverse sensor /2 (PS45) does not turn ON within a specified period of time after the reverse sensor /1 (PS48) turns ON. |
|
J-9202 |
During operation: While in drawing, the reverse sensor /2 (PS47) does not turn OFF within a specified period of time after the ADU reverse sensor /2 (PS45) turns ON. |
|
J-9203 |
During operation: The ADU conveyance sensor / 1 (PS35) does not turn ON within a specified period of time after the start from the 1st stop position. |
|
J-9252 |
When idling: The ADU reverse sensor /2 (PS45) turns ON while in idling. |
|
J-9253 |
When idling: The paper stay sensor /1 (PS64) turns ON while in idling. |
|
J-9254 |
When idling: The paper stay sensor /2 (PS63) turns ON while in idling. |
|
J-9301 |
During operation: The ADU exit sensor (PS43) does not turn ON within a specified period of time after the ADU conveyance sensor /1 (PS35) turns ON. |
|
J-9351 |
When idling: The ADU reverse sensor /1 (PS35) turns ON while in idling. |
|
J-9352 |
When idling: The ADU reverse sensor /2 (PS36) turns ON while in idling. |
|
J-9401 |
During operation: After the start from the 2nd stopping position, the ADU deceleration sensor (PS42) does not turn ON within a specified period of time. |
|
J-9451 |
When idling: ADU exit sensor (PS43) turns ON while in idling. |