КОДЫ ОШИБОК RISO TR
No. |
Display Condition |
Resetting Method |
E01 |
Main Motor Lock • If excessive current is detected 0.3 seconds consecutively after the Main motor is activated. • If no Encoder sensor output after Main motor is activated. |
Press ALL RESET button. |
E02 |
Elevator Motor Lock • When the light path of the Upper limit sensor or the Lower limit sensor is not cut within 10 seconds after the Elevator motor is activated. • If the light path of both the Upper limit and Lower limit sensors are blocked when the Elevator motor is activated. • If excessive current is detected 0.3 seconds consecutively after the Elevator motor is activated. |
Press ALL RESET button. |
E03 |
Clamp Motor Lock [During Clamp Motor Initial Positioning] • If the light path of the Clamp senors both A and B are not opened within 13 seconds after after the Clamp motor is activated. [During Master Release from the Clamp Plate] • If the light path of the Clamp sensor B is not blocked within 3 seconds after the Clamp motor is activated. • If the light path of the Clamp sensor B is not opened within 12 seconds after the Clamp motor is activated. [When the Clamp Plate opens during Master Clamping] • If the light path of the Clamp sensor B is not blocked within 3 seconds after the Clamp motor is activated. • If the light path of the Clamp sensor A is not opened within 5 seconds after the Clamp motor is activated. [When the Clamp Plate closes during Master Clamping] • If the light path of the Clamp sensor B is not opened within 5 seconds after the Clamp motor is activated. |
Press ALL RESET button. |
E04 |
Ink Overflow • If the Overflow sensor detects excessive ink in the Squeegee unit. |
Remove excess ink from the Drum. |
E05 |
Print Positioning Motor Lock • If the Vertical centering sensor status has not been changed from ON to OFF (or OFF to ON) within 3550 ms after the Print positioning motor activated. |
Press ALL RESET button. |
E06 |
Position-A Sensor Malfunction • If Position-A sensor cannot be detected (or keeps detecting) even though the Main motor encoder sensor signal is making the output after the Main motor is activated. |
Press ALL RESET button. |
E07 |
Master Compressing Motor Lock [When compressing] • If the light path of the Master compressing sensor is not opened within 10 seconds after the Master compressing motor is activated. [When returning back] • If the light path of the Master compressing sensor is not opened (or closed) within 1 second after the Master compressing sensor is activated. |
Press ALL RESET button. |
E08 |
Communication Error between TR and Interface Accessaries • If a communication error has occurred between the CPU and the interface accessaries. |
Turn Power SW OFF & ON. |
E10 |
Shading Error • If the Shading compensation is not made. |
Turn Power SW OFF & ON. |
E13 |
Cutter Motor Lock • If the Cutter position sensor is not turned OFF within 75 ms after the Cutter motor is activated. • If the Cutter position switch is not pressed within 450 ms after the Cutter motor is activated. |
Drum Set Sensor OFF & ON. |
E14 |
Master Removal Motor Lock • If excessive current is detected 0.3 seconds consecutively after the Master removal motor is activated. |
Press ALL RESET button. |
E15 |
Master Tension Plate Lock • If the light path of the Master tension plate sensor is not blocked within 384 pulse rotation of the Read pulse motor rotated in the reverse direction. • If master loading error is detected at Drum angle 79° and if the Master tension plate sensor is blocked. |
Press ALL RESET button. |
E16 |
Inking Motor Lock • If excessive current is detected 0.3 seconds consecutively after the Inking motor is activated. |
Press ALL RESET button. |
E20 |
Paper Ejection Motor Lock • If excessive current is detected 0.3 seconds consecutively after the Paper ejection motor is activated. |
Press ALL RESET button. |
E50 |
Connect "Copy/Master" Counter • If the connector of the Counter is not connected. |
Connect Counter. |
E77 |
No TPH code • If the TPH code is not output to the machine. (Connector loose) |
Press ALL RESET button. |
E78 |
Machine Model Selection Error • If Memory switch No.200 is selected to 9~F. |
Select to correct setting. |
(C21) |
Master Loading Error (onto the Drum) • If the Master sensor does not detect the master (light not reflected) during the master loading when the Drum is at 79° from the position-A. |
Master Making Unit Set SW OFF &ON. |
(C22) |
Master Misfeed • If the Master positioning sensor does not detect the master (light not reflected) within 944 pulses after the Write pulse motor activates. • If the light path of the Master tension plate sensor is blocked (Master tension plate is down) when the master feeding has started. |
Master Making Unit Set SW OFF &ON. |
(C23) |
Master Cut Malfunction • If the Master positioning sensor is still detecting the master (light reflected back) when the Drum is at position-A after the cutting operation and the Master tentioning plate sensor is ON. |
Drum Set Sensor OFF & 2 seconds later ON. |
(C25) |
Master Removal Error • If the Master removal sensor does not detect the removed master (light path opened) when the Drum rotates to either 70° or 90° from the position-A during the master removal, when a master was detected on the Drum. |
Drum Set Sensor OFF & 2 seconds later ON. |
(C26) |
Removed Master Jammed at the Master removal area • If the Master removal sensor is detecting the removed master (light path blocked) even though the Drum has returned to the position-A after the master removal process. |
Unblock the light path of the Master removal sensor. • Remove the jammed master. |
(C27) |
No Master on the Drum • If the Master sensor does not find master on the Drum when the Drum is at 79° during the printing movement. |
Press ALL RESET button. |
(C31) |
Paper Jam in the Second Paper Feed Area • If the Paper receiving sensor does not find paper when the Drum is at Position-A during the printing operation and the Paper sensor finds a paper at next Drum Position-A. |
Press ALL RESET button. • Remove the jammed paper. |
(C32) |
Paper Jam in the Paper Receiving Area • If the status of the Paper receiving sensor does not change from detecting paper to not detecting from one Drum Position-A to the next during printing. |
Press ALL RESET button. • Remove the jammed paper. |
(C33) |
Paper Jam in the First Paper Feed Area • If the Paper sensor does not detect paper at Drum angle 135° within three Drum rotations during printing. |
Press ALL RESET button. |
(C34) |
Paper Jam on the Drum • If the Paper receiving sensor does not detect paper at one Drum Position-A and the Paper sensor detects paper at next Drum Position-A. |
Drum set sensor OFF & 2 seconds later ON, or press ALL RESET button. |
(C37) |
Original Jam at Entrance • During the Original set movement, if the Original IN sensor does not detect Original (sensor light not reflected) within 1712 pulses after the Read pulse motor activates. • During the Original set movement, if the Original IN sensor stops detecting the Original before the Read pulse motor activates 347 pulses. |
ADF set sensor OFF & ON. |
(C38) |
Original Jam or Oversize • During the Original scanning, if the Original IN sensor keeps detecting Original (sensor light reflected) and does not stop detecting within 4945 pulses after the Read pulse motor activates. |
ADF set sensor OFF & ON. |
(C41) |
Replace Ink Pack • If the Ink sensor does not detect ink in the Squeegee unit within 20 seconds after the Inking motor was activated. • If the Ink sensor does not detect ink in the Squeegee unit within 80 seconds after the Drum idling has started. |
Ink pack set sensor OFF & 5 seconds later ON. |
(C42) |
Replace Master Roll • If the black tape attached at the end of the Master roll has been detected by the Master end sensor during master making or confidential operation. |
Master making unit set SW OFF &ON. • Replace the depleted Master roll with a new one. |
(C43) |
Empty Disposal Box • If the Master full detection sensor does not detect the Master compress plate during the master compressing process. |
Master removal set switch OFF & 5 seconds later ON. • Empty the disposal box. |
(C44) |
Add Paper • If the light path of the Paper detection sensor is open. |
Paper detection sensor ON. • Add paper on the Paper feed tray. |
(C49) |
Close Master Removal Unit •If the actuator of the Master disposal unit set switch is not depressed. |
Close the Master removal unit. |
(C51) |
Insert Card into Key/Card Counter • If an operator card is not set in the Key/Card counter. |
Insert the card. |
(C52) |
Set Drum in Place • If the Drum set sensor does not detect the Drum. |
Set the Drum in the machine. |
(C53) |
Set Ink Pack in Place • If the Ink pack set sensor does not detect the Ink pack. |
Set the Ink pack in the Drum. |
(C56) |
Close ADF Unit • If the ADF unit set sensor does not detect the ADF unit. |
Close the ADF unit. |
(C58) |
Close Master Making Unit • If the actuator of the Master making unit set switch is not depressed. |
Close the Master making unit. |
(C61) |
Drum size error • If Memory switch No.200 is selected to wrong machine model or wrong model Drum is set in the machine. |
Set correct Drum in the machine or set Memory switch No.200 to correct machine model setting. |